User's Manual

2.9 TH_CURV
TH CURV THROTTLE CURVES
This function makes the throttle high side and brake side direction servo operation
quicker or milder. It has no effect on the servo maximum operation amount. For the high
side, selection from among three kinds of curves (EXP/VTR/CUR) is also possible.
Note: When the course conditions are good and there is no sense of torque at the power
unit, set each curve to the + side (quick side). When the road surface is slippery and the
drive wheels do not grip it, set each curve to the - minus (mild) side.
Note: Brake side only has EXP curves.
1 Press “ENTER” to see FUNCTION MENU
2 Use the +/- Keys to select the TH CURV function and press ENTER.
3 Press ENTER to select a setting.
4 Use the +/- Key to change the value.
5 Press EXIT to save and return to FUNCTION MENU, press EXIT again to return to the
Main Screen.
STEERIN G STEERIN G
M:0 %
H:100%
T H _ C U R V 1 0 . 2 V
M : E X P
4 3 R :
B R : 0
STEERIN G STEERIN G
M:0 %
H:100%
T H _ C U R V 1 0 . 2 V
Neutral
Neutral
Quick forward(R:0~100)
Mild forward(R:-100~0)
STEERIN G STEERIN G
M:0 %
H:100%
T H _ C U R V 1 0 . 2 V
Neutral
Mild backward(BR:-100~0)
TH. POS
TH. POS
Adjustment method for EXP curve
--Select EXP at setup item “M”
--Select setup item “R” and make the following adjustments:
1.Forward side adjustment:
Use the (+) button to adjust the + side when you want to quicken the rise and use the(-)
button to adjust the - side when you want to make the rise milder.
2.Brake side adjustment:
Select the setting item "BR" by ENTER button and use the (+) button to adjust the + side
when you want to quicker the rise and use the (-) button to adjust the - side when you want
to make the rise milder.
3.When ending setting, return to the initial screen by pressing the EXIT.
M : E X P
- 3 2 R :
B R : 0
M : E X P
R : - 3 2
: - 8 0B R
R/C Introduction Manual
10
R/C Introduction Manual
9
This function is used to change the sensitivity of the steering servo around the neutral
position. It has no effect on the maximum servo travel.
Note: When the setting is not determined, or the characteristics of the model are
unknown, start with 0% ( when EXP is set to 0%,servo movement is linear)
1.Press “ENTER” to see FUNCTION MENU
2.Use the +/- Keys to select the ST CURV function and press ENTER.
3.Use the +/- Key to change the value.
4.Press EXIT to save and return to FUNCTION MENU, press EXIT again to return to the
Main Screen.
STEERING CURVER adjusting value range: -100%~+100% Default is 0%(Linear)
Steering EXP adjustment
1.When you want to quicken steering operation, use the (+) button to adjust the + side.
When you want to make steering operation milder, use the (-) button to adjust the - side.
2 .When ending setting, return to the function menu by pressing the (EXIT) button .
TERMS: M-MODE, R--RATE
2.7 REV
This function reverses the direction of operation of
the servos related to transmitter steering, throttle, and
channel 3 operation.
1.Press “ENTER” to see FUNCTION MENU.
2.Press “+” or “-“ to choose REVERSE, and
press “E NTER” to enter REVERSE adjusti ng
interface.
3.Press “ENTER” to choose each Channel.
4.Press “+” to increase and “-” to choose
“REV” or “NOR”.
R E V E R S E 1 0 . 2 V R E V E R S E 1 0 . 2 V
T H A U X S T
R E V
N O R
5.Press “EXIT”to save your setting and leave REVERSE interface, and back to the
function menu interface.
Note: However, when the position set by trim or sub trim shifts from the center, the
center becomes the opposite side.
TERMS: ST-STEERING, TH-THROTTLE,AUX-AUXILLIARY
2.8 ST_CURV
S T _ E X P 1 0 . 2 V
M : E X P
R : 0 %
S T _ E X P 1 0 . 2 V
F u n c t i o n 1 0 . 2 V F u n c t i o n 1 0 . 2 V
5 : S T C U R V
6 : T H C U R V
7 : A B S
8 : M O D E L
M : E X P
R : 5 0 %