User's Manual

ManualsBrandsGuangzhou H & F Electronics Technology ManualsComputers & AccessoriesWiFi Repeater

Wireless-N Wifi Repeater

For more information:

http://windows.microsoft.com/en-US/windows7/Add-a-device-or-computer-to-a-network

http://windows.microsoft.com/en-US/windows7/Setting-up-a-wireless-network

http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-wireless-network

Adding a Wireless computers to the WiFi-Repeater with WPS Button

1. Log on to the computer.

2. Press the WPS button of the WiFi Repeater directly for 2 - 3 seconds.

3. Press the WPS button of the Wireless Adapter directly for 2 - 3 seconds. Click

Finish to complete the WPS configuration. (Please check your Wireless adapter

Manual with WPS configuration)

4. You should see icons for the computer you added and for the other

computers and devices that are part of the network.

1. Plug the Wi-Fi Repeater to a wall socket. Connect your computer / laptop with the

Wi-Fi Repeater with enclosed RJ45 Cable.

2. To confirm that you added the computer, do the following:

Open Network by clicking the Start button , and then clicking Control Panel. In

the search box, type network, and then, under Network and Sharing Center, click

View network computers and devices. You should see icons for the computer

you added and for the other computers and devices that are part of the network.

Adding a wired (Ethernet) computer to the WiFi-Repeater

A6. Select your SSID to continue.Wireless

A7.

Wireless-N Wifi Repeater

How to connect your computer/laptop with the

Wi-Fi Repeater

Adding a Wireless computers to the WiFi-Repeater

1. Log on to the computer.

2. Open Connect to a Network by right-clicking

the network icon ( or ) in the otification

area.

3. Choose the wireless network from the list

that appears, and then click Connect.

4. Type the network security key or passphrase

if you are asked to do so, and then click OK.

You'll see a confirmation message when you

are connected to the network.

5. To confirm that you added the computer, do the following:

Open Network by clicking the Start button , and then clicking Control Panel. In

the search box, type network, and then, under Network and Sharing Center, click

View network computers and devices. You should see icons for the computer

you added and for the other computers and devices that are part of the network.

Note : If you don't see icons in the Network folder, then network discovery and

file sharing might be turned off.

4. The following message will be displayed on your web browser:

B. Configure the Wi-Fi Repeater with RJ45 Cable.

1. Plug the Wi-Fi Repeater to a wall socket. Connect your computer / laptop with the

Wi-Fi Repeater with enclosed RJ45 Cable.

2. Follow process A3 to A7 to configure your Wi-Fi Repeater.

C. Configure the Wireless AP Mode.

1. Plug the Wi-Fi Repeater into a wall socket.

2. Follow process A3 to A4.

3. Click on ‘AP’ to continue.

Click on ‘Apply’ button, The Repeater will restart.

Wait a few seconds your Wi-Fi Repeater is ready for use.

SSID

Channel

Security type

The "SSID" of your wireless network.

Auto (recommend)

Setup the wireless security and encryption to prevent from

unauthorized access and monitoring.

Supports 64/128-bit WEP, WPA, WPA2, WPA/WPA2 encryption

methods.

Security key The "Password" of your wireless network.

of your network.

When you see below, please do not change any setting but only insert the key

Click on ‘Apply’ button, The Repeater will restart.

Wait for a few seconds your Wi-Fi Repeater is ready for use.

* The default wireless SSID and Security key of Wi-Fi Repeater is same as your

AP/router.

Repeater

Wizard

User-PC Repeater WAP/Router Internet

Wireless status

Wireless

Management Status

Internet

Mode AP

Stauts Enabled

SSID Wifi-Repeater

Channel 1

Security Disabled

Clients 0

Basic settings IP 192.168.10.1

DHCP Server

MAC 80:3f:5d:81:96:c1

Firmware version

RptM.321.38.1119

Uptime

RptM.321.38.1119

Build time

Mon Nov 19 11:35:57 CST 2012

Advanced settings

WPS

Schedule

Time zone settings

Password

Save/Reload settings

Upgrade Firmware

Network 6 WAP2-PSK

Your SSID

Network’s passwork

Apply

Your SSID

Auto

WPA/WPA2 PSK

Your passwork

Connect automatically

Connect

Wireless-N Wifi Repeater

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitly approved by manufacturer could void your authority to operate this

equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator and your body.