Installation Instructions

ManualsBrandsGuangzhou Shikun Electronics ManualsElectronicsIEEE 802.11b/g/n/a/ac/ax 2T2R USB WiFi Module Integrated BT 2.1+EDR/4.2/5.2

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC regulations restrict the operation of this device to indoor use only.

Operations in the 6GHz bands:

1) 5.925-7.125GHz band are restricted to indoor usage only.

2) The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that

operation of this device is permitted in large aircraft while flying above 10,000 feet.

3) Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications

with unmanned aircraft systems.

This device meets all the other requirements specified in Part15C, Section 15.247 and Part 15E, Section 15.407

of the FCC Rules.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part

of your body.

The device must be professionally installed. The intended use is generally not for the general public. It is generally for

industry/commercial use.

Installation must be controlled. Installation requires special training.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and users,

and

2) The transmitter module may not be co-located with any other transmitter or antenna.

The OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed.

3) PFF restriction:

⚫ FCC regulations restrict the operation of this device to indoor use only.

⚫ Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications

with unmanned aircraft systems.

⚫ This device is limited to under control of a low-power indoor access point (6ID) or subordinate (6PP).

⚫ This device cannot have a direct connection to the internet.

Summary of content (3 pages)

PAGE 1
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 2
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. The module is tested for standalone mobile RF exposure use condition.
PAGE 3
The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB 996369. OEM/Host manufacturer responsibilities Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons.