User's Manual

Bluetooth
ON
Connect
BS346GC
TWS Pairing
TWS Pairing
1. Long touch the panel for 2 seconds to turn on, the earbuds will
enter auto-pairing mode, waiting for a few seconds, the two
earbuds will pair automatically, then use mobile to search .
2. Open the charging case cover, the earbuds in case will enter
auto-pairing mode, waiting for a few seconds, the two earbuds will
pair automatically, then use mobile to search.
1. After TWS pairs successfully and
connected with the mobile, the earbuds
prompt “connected”.
2. When the earbuds disconnects with the
mobile, the earbuds prompt “Disconnect-
ed”, and the master earbud enters pairing
mode.
If the earbuds don’t connect with mobile
within 5 minutes, they will turn off automati-
cally.
Pairing with Mobile
Do as the above ways:
Using the mobile to search “BS346GC” and
select it from Bluetooth list (Please refer to
the bluetooth device user manual).
After connected with Bluetooth device, the
earbuds will prompt “connected”.
When call coming, long touch the
earbud(R/L) for 2 seconds to reject
the call.
Reject a call
Answer / End a Call
When call coming, double tap the earbud(R/L) to answer the call.
In phone calling mode, double tap the earbud(R/L) to end the call.
Voice Assistant
In connection mode, triple tap the earbud(L) to activate voice
assistance, then triple tap the earbud(L) to exit.
Gaming Mode
In Power ON Mode, triple tap the earbud(R) to enter gaming mode,
R&L prompts “Gaming mode on”, then triple tap the earbud(R) to
exit gaming mode, R&L prompts “Gaming mode off”.
Next / Previous Track
Reset
Put the earbuds in the charging case, open the charging case cover
and long press the reset button for 10 seconds, the charging case
indicator flashes blue for 10 seconds quickly. Waiting until the
indicator light turns off.
Maintenance
Trouble Shooting
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Trouble Reasons Solutions
The earbuds fail to
reconnect / earbuds noisy,
can not operate
The earbuds broken down Put the earbuds into the charging
case and close the cover for 20
seconds to let earbuds resume
normal
Low battery Charge the earbuds for 1-2 hours
Earbud echo
Noise in call Change place or go back to
working range
Adjust volume on phone or
change a place
Without enough battery
capacity in the charging
case or earbuds
Charge the earbuds and case
at same time for 1-2 hours, to
ensure that the product has power
Pairing failure or pairing
overtime
Without enough battery
capacity in charging case /
earbuds metal pin poor
contact
Low voice of the calling
party
Wrong Wearing
Follow wearing instructions
Turn off automatically
No sounds after pairing
Volume is too loud or
environment is noisy
Environmental interference
or out of working range
The earbud fails to connect
with mobile
The charigng case has no
indication after the
earbuds are put inside
Reset the earbuds and repairing
Charge the case for about 1-2 hours/
check whether the earbuds are put in
position or the dirty matal pin leads to
poor contact
One earbud no sound
after connect with
mobile
The charging case flashes
blue every 1 second
Earbuds metal pins might be
dirty, leading to short and
over current, activating
over-current protection
Earbuds single / double /
triple touch failure
Clean the earbuds metal pin, put the
earbuds back to the charging case,
close and open the top cover,
earbuds will resume normal
Double / Triple touching should be
finished within 700ms. Put the
earbuds to the charging case to
wake up if touching operation failure
Time of double / triple touch
is too long or touching
operation failure
Block the mic hole during
touch
TWS Reconnected
Method 1:
Method 2:
Touch the earbud(R/L) for 2 seconds to power on → wait
for a few seconds, the two earbuds will connect
automatically
→ the earbuds will connect with the mobile
phone that has ever paired after a few seconds
→
reconnected successfully.
Open the charging case to power on
→ wait for a few
seconds, the two earbuds will connect automatically
→
the earbud will pair with the mobile phone that has ever
paired after a few seconds
→ reconnected successful-
ly.
Single Pairing Mode by Manual
1. If without pairing record, double tap the panel after turning on, the
earbuds will enter into pairing mode, and keep for 1 minute.
2. If TWS has pairing record, please turn off the bluetooth function
of connected devices firstly. The earbud will enter into pairing mode
after 10 seconds and keep for 1 minute. ( During pairing mode, if
turn on the other earbud, they will connect.)
Two-call Handling
When you are answering a call, there is another call coming :
1. Long touch the earbud(R/L) for 2 seconds to end the current
call and answer the incoming call;
2. Double tap the earbud(R/L) to hold the current call and answer
the incoming call;
3. After the second implementation, double tap the earbud(R/L) to
switch between two calls;
4. After the second implementation, long touch the earbud(R/L)
for 2 seconds to end the current call, and double tap the
earbud(R/L) to end the other call.
Note:
To use the above functions, the mobile must support the Bluetooth
hands free profile V1.5 and the mobile holding function (Network
services from telecom) from has been started.
Music Playing/Pause
In music playing mode, single touch the
earbud (R/L) to pause music;
In pause mode, single touch the
earbud (R/L)
to play music.
ANC / Transparency Mode Switch
In Power ON Mode, long touch the earbud(R/L) for 2 seconds to
switch normal / transparency / ANC mode.
In ANC mode, R&L prompts “ANC on”, in transparency mode, R&L
prompts “Transparency on”, in normal mode, R&L prompts “All off”.
Unable to turn on by
opening charging case
cover or touching earbuds
area
TWS paired, but can not
search in mobile
The earbuds has too many
pairing records
Reset the earbuds and repairing
Reset the earbuds and repairing
The earbuds fluzzing
when touch the area
Resume normal after put hands
down
Without obvious ANC
effect
Earmuffs sealing not good
Adjust to correct wearing position
or replace with suitable earmuffs
size, to ensure the earmuffs fit
for wearing
Do not use abrasive cleaning solvents to clean your earbuds.
Prevent your earbuds from touching any sharp objects.
Keep your earbuds away from high-temperature, humidity and dust.
When in playing music mode, double tap the earbud(R) for next
song. Double tap the earbud(L) for previous song.