ww walkers — i BAR W/IKCSZ20605] User Manual Note: read though the manual before operation and keep It In a safe place for the future reference.
Part one: General Information 1.0 Foreword toms meme 1 1.1 Important Statements ona 1 1.2 Safety Guidelines Needing Attention 1 1.3 Attention before flight == ceca 2 2.0 Features mmm 3 2.1 Transmitter WK-2603 k] 3.0 Specification ~~ «oven Transmitter Specification 3 3.2 Receiver Specification 3 40FaC8 mmm mmm ee 4 4.2 Wiring Diagram ~= owner mmm 8 4.3 WK-2603 Input Key Function wee eeemvommcncannnan 7 5.0 Control Stick Length Adjustment 7 5.1 Control Stick Tension Adjustment «wae eeemwunnn. 7 5.
Party two: Function Setup 1.0 Main Menu «mmm Swash plats type 12 3. 0 Channel reverse 13 buzzer setup
Part one: General information 1.0 Foreword The WK-2603 adopts the frequency-hopping spread spectrum 2.4G technology which features automatic code pairing, ID assignment and high capacity of anti-jamming. it uses the graphic menu which features simple easy-to-read operation. 1.1 important Statements {1) The transmitter is suitable for experienced radio controlled helicopter modelers beyond 14 years old. {2} Flying the model aircraft in approved ground is a must.
{3} Proper operation Please use Walker original spare parts to upgrade, modify or maintain your equipment in order fo assure its safely. Please operate your equipment within the range of functions permitted. It is forbidden to uss of the safety laws or regulations. {4) Safety operation Please fly your equipment according to your body status and flight dildos. Fatigue, listlessness and miss-operation will increase the possibilities of accidental hazard.
lo 2.1 Transmitter WK-2603 1. The WK-2603 adopts 2 4G frequency-hopping spread spectrum technology and features automatic code pairing and ID assignment. 2. Graphic display menu is simple to understand and fo set. 3.The appearance design accords with ergonomics and features easy holding. The LCD screen with back light and graphic interface looks more personalized, 4. Both the length and tension of the stick can be adjustable. It is convenient fo freely switch among the 4 stick modes. 3. 0 Specifications 3.
Antenna V1 knob Gear Throttle limited height switch Elevator Trim Elevator / Rudder Stick Rudder Trim UP / DOWN Function EXT Function Key LCD Neck Strap Eyelet V2 knob Hg Flight Mode SW ELEV/AILE/RUDD Throttle Trim Throttle / Aileron stick Power SW Aileron Trim increase / Decrease Function Key ENT Function Key
4.1 Back Charging Jack: Input Voltage: 12V, Current: 50-100mA. Polarity: it's only fit for the rechargeable battery pack. Non-rechargeable one is strictly forbidden fo use the charge function! Analog signals output jack! training jack (DISC: for simulator flight practice via computer {You need a software and its dongle which are available in hobby stores), and for training.
4.
4.3 WK-2603 input Key Function EXT: Reset key, press EXT to exit the setting mode. ENT: Enter key, press ENT to enter the setting and confirmation status. ‘UP: Selection key, moves cursor up to the previous function item. ‘DN: Selection key, moves cursor down to the next function item. +R: Change the setting. L-: Change the setting. 5.
5.3 Mechanical throttle switch methods 5.3.1 Right-hand throttle switched to left-hand throttles A. The stick position change Remove the battery pack and the 8 fixing screws in the back of transmitter, and then remove the transmitter back case {Be careful not to break the wires inside). Use a Phillips screwdriver to loosen the linkage screws, screw A, screw B and the throttle arresting spring int the right thriftless position. Then mount them {o the corresponding positions in the left throttle position.
5.3.2 Left-hand throttle switched to right hand A. The stick position change Remove the battery pack and the 8 fixing screws in the back of transmitter, and then remove the transmitter back case {Be careful not to break the wires inside}. Use a Phillips screwdriver fo loosen the linkage screws, screw A, screw B and the throttle arresting spring in the left throttle position. Then mount them to the corresponding positions in the right throttle position.
