User's Manual

22-0369v1.7 G-PROX / G-PROX II INSTALLATION REFERENCE
CSG Security Corp / Sécurité CSG Corp Page 2 of 3
GUARDAL
L
5201 Explorer Drive, Mississauga, Ont., Canada. L4W-4H1
[e-mail] +1 905.206.8434 | support@ guardall.com +1 905.206.8436 | Fax: [phone]
www.guardall.com | +1 877.249.9993
Reader Mounting:
Standard readers can be surface mounted, or flush mounted.
Flush Mount
: Use the rear cover only as a template to mark the cut-out (L-
shaped notches). Surface Mount
: Use the rear cover for mounting onto the
wall. The reader mounts onto the rear cover using the two self-tapping screws
provided. Do NOT over tighten mounting screws.
6.5 cm
8.5 cm
2
3
9/16
11/32
Note: When selecting a mounting height, consider physically-challenged persons as
well.
Reader Wiring: Refer to the tables
below when connecting your specific reader:
Standard Reader and Arming Station
Wiring:
Notice: Do all wiring with the door
controller powered down, or
ensure
the +12V is never connected without
the 0V/Gnd first.
Signal
(Connect to)
G-Prox II Reader
G-Prox II Arming
Station
G-Prox Series I
Reader (no
keypad or matrix)
G-Prox Series I
w/ Wieg
. keypad
(rdr or
Arm. Stn.)
Your Wire Colour
(Reader Extension Cable)
Power (+V)
Red Red Red Red
Signal Gnd / 0V
Black Black Black Black, Brown
Data 0
Green Green Green Green
Data 1
White White White White
Red LED
Brown Yellow Brown Blue
Green LED
Orange Orange Orange Orange
Buzzer Output
— — Blue —
+ trig. for buz.
— Grey —
Gnd trig. for buz
Yellow
— Yellow Yellow
Not used
Additional
colours
Additional
colours
Additional
colours
Additional
colours
—
MATRIX-Style Keypad Wiring (2nd / left-hand cable, if present)
Wire / Colour
(2nd Reader Cable)
Connection at Door
Controller / Module
Your Wire Colour
(Reader Extension Cable)
Brown SL0
Green SL1
White SL2
Blue SL3
Orange RL0
Yellow RL1
Grey RL2
- Key / Lock Code: A “lock code” can
prevent a dealer from attempting to take
over another dealer’s customer.
If a dealer orders a G-Prox II system to
produce cards, add readers to their
customer base, they can receive these
parts:
• Generic Software
• A Desktop Card Programmer
• Blank Access Cards
• G-Prox II Readers
• A unique License Number
When the unique license number is
entered into the software, it will program in
an exclusive “lock code” if it was ordered.
When a reader configuration card is
programmed, this unique lock code will be
transferred to it. When readers are
programmed with the configuration card,
their default lock code of “1” will be
changed to a unique one. When user
cards are programmed, the same unique
lock code will be transferred to them.
Matching lock codes at a location are
necessary to unlock doors.
WARNING: A configuration card with a
different lock code, such as another
dealer’s lock code, can not be used to
program G-Prox II readers at a location
that does not use the same lock code.
During the first 15 minutes that a G-Prox II
reader is powered, the configuration card
is applied to the reader to program it with
e.g. the lock code. The lock code can only
be programmed ONCE. De- and re-
powering the reader to re-start the 15
minute reader programming period to re-
apply a configuration card with a correctly
matching lock code will not change the
lock code. The reader will have to be
returned to the Factory for the lock
code to be re-set. User cards can not be
programmed for a location with software
that does not use the same lock code.
Reader programming can be done either before
or after installation. (Power up, then present a
suitable programming card within 15 minutes to
each reader.)
Cards and readers can be ordered from your
supplier with a lock code default of “1” or as the
software system with special lock code and
programming using the G-Prox™ Desktop Card
Programmer. For details, refer to the on-line
help or user's guide, P/N 22-0354 (provided with
that software.)
Default Settings for Programmable
Features
• Key / Lock Code: 1 (matches the
default for cards);
• LED: Bi-colour operation;
• Buzzer: Active low (sounds when
Yellow wire is grounded);
WARNING: Readers must not be mounted back to back on a wall.