Product Name: Horizontal Lifeline (HLL) System Part #: 04625; 04628; 04629; 04630; 04637; 04638; 04639; 04640; 14639 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards 1 Worker Classifications 1 Product Specific Applications 2 Limitations 2-3 Components and Specifications 3-4 Installation and Use 4 Maintenance, Cleaning, and Storage 5 Inspection 5 Inspection Log 5 Safety Infor
Serial #: Trainer: User: Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1-2007, and ANSI A10.32-2012 standards for fall protection. Applicable standards and regulations depend on the type of work being done, and also might include state-specific regulations. Consult regulatory agencies for more information on personal fall arrest systems and associated components.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Product Specific Applications ! WARNING Use of equipment in unintended applications may result in serious injury or death. Maximum 1 attachment per connection point. Personal Fall Arrest: HLL System may be used to support a MAXIMUM 2 PFAS for use in Fall Arrest applications. Structure must withstand loads applied in the directions permitted by the system of at least 5,000 lbs.
Connector closed and locked to D-ring. OK. Connector to integral lanyard. NO. Incompatible or irregular application, which may increase risk of roll-out. NO. Connector directly to webbing. NO. Two connectors to same D-ring. NO. Two or more snap hooks or carabiners connected to each other. NO. www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Compatibility: When making connections with HLL System, eliminate all possibility of roll-out.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Ultra Sack (1) Rope Lifeline (1) Cross Arm Strap (2) Carabiner (2) O-ring (2) Rope Tensioner (1) Tensioner Nut Installation and Use Prior to use, plan your system: 1. Ensure all PFAS equipment is selected and deemed compatible by a Competent Person. 2. Eliminate or minimize all risk of swing fall. 3. Determine desired location for HLL; ensure location is free of debris, rot, decay, cracking, and hazardous materials. 4.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals, or other degrading elements. Inspection Prior to EACH use, inspect HLL System for deficiencies, including, but not limited to, corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, and missing or illegible labels.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Safety Information ! WARNING Failure to understand and comply with safety regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. Do not misuse equipment.
Kernmantle HLL Part #: Date of Manufacture: Prior to use, read and understand all manufacturer’s instructions provided with equipment at time of shipment. Compliant with all applicable OSHA 1910, OSHA 1926 Subpart M, ANSI Z359.1-2007, and ANSI A10.32-2012 regulations. Worker capacity range: (including all equipment) 130-310 lbs. MAXIMUM 2 workers per Kernmantle HLL. Materials: Polyester, galvanized steel, and zinc-plated steel. All PFAS equipment must be selected and deemed compatible by Competent Person.
