Product Name: 4-in-1 Big Boss Lanyard Part #: 11520; 11521; 11522 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards 1 Worker Classifications 1 Product Specific Applications 2 Limitations 2-3 Components and Specifications 3 Installation and Use 4 Maintenance, Cleaning, and Storage 5 Inspection 5 Inspection Log 5 Safety Information 6 Labels 7
Date of First Use: Serial #: This and any other included instructions must be made available to the user of the equipment. The user must understand how to safely and effectively use the 4-in-1 Big Boss Lanyard, and all fall safety equipment used in combination with the 4-in-1 Big Boss Lanyard. Trainer: User: Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.13-2013, and ANSI A10.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Product Specific Applications ! WARNING Use of equipment in unintended applications may result in serious injury or death. Maximum 1 attachment per connection point. Personal Fall Arrest: 4-in-1 Big Boss Lanyard may be used to support a MAXIMUM 1 Personal Fall Arrest System (PFAS) for use in Fall Arrest applications.
Two or more snap hooks or carabiners connected to each other. NO. Connector directly to webbing. NO. Two connectors to same D-ring. NO. Application that places load on gate. NO. Incompatible or irregular application, which may increase risk of roll-out. NO. Connector directly to horizontal lifeline. NO. Components and Specifications Materials: nylon, polyester, and galvanized steel.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Installation and Use Prior to use, plan your system: 1. Prior to use, inspect Guardian 4-in-1 Big Boss Lanyard and all PFAS equipment to be used in combination with 4-in-1 Big Boss Lanyard. 2. Ensure that all connectors and all other components of the PFAS are compatible with Guardian 4-in-1 Big Boss Lanyard, and are selected by a Competent Person.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals, or other degrading elements. Inspection Prior to EACH use, inspect 4-in-1 Big Boss Lanyard for deficiencies, including, but not limited to, corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, and missing or illegible labels.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Safety Information ! WARNING Failure to understand and comply with safety regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. Do not misuse equipment.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Labels Material: Polyester and galvanized steel. Compliant with OSHA 1926 Subpart M, ANSI Z359.13-2013, and ANSI A10.32-2012. Immediately remove this lanyard from service if exposed to forces of fall arrest. Attach shock absorber end of lanyard to fall arrest D-ring on harness. DO NOT REMOVE LABELS 90033 (Rev. B) ! WARNING USER MUST INSPECT BEFORE EACH USE. Maximum Elongation: 60” Make only safe, compatible connections.
