Product Name: Cyclone Harness Series Part #: 21064; 21065; 21066; 21067; 21033; 21034; 21035; 21036; 21029; 21030; 21031; 21032; 21052; 21053; 21054; 21055; 21045; 21046; 21047; 21048; 21041; 21042; 21043; 21044; 21082; 21083; 21056; 21057; 21058; 21060; 21061; 21062 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards 1 Worker Classifications 1 Product Specific Applications 2 Limitations
User Information Date of First Use: Serial #: Trainer: User: Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1-2007, and ANSI A10.32-2012 standards for fall protection. Applicable standards and regulations depend on the type of work being done, and also might include state regulations if applicable.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Product Specific Applications ! WARNING Use of equipment in unintended applications may result in serious injury or death. Maximum 1 attachment per connection point. Personal Fall Arrest: Cyclone Harness may be used to support a MAXIMUM 1 PFAS for use in Fall Arrest applications. Structure must withstand loads applied in the directions permitted by the system of at least 5,000 lbs.
Connector to integral lanyard. NO. Two or more snap hooks or carabiners connected to each other. NO. Connector directly to webbing. NO. Two connectors to same D-ring. NO. Application that places load on gate. NO. Incompatible or irregular application, which may increase risk of roll-out. NO. Connector directly to horizontal lifeline. NO. Components and Specifications Materials: polyester, nylon, steel, and aluminum.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 USA Guardian Fall Protection Installation and Use All personal fall arrest system (PFAS) equipment must be selected and deemed compatible with Cyclone Harness by a Competent Person. ALWAYS follow all instructions of all equipment used in combination with Cyclone Harness. NEVER attach connector to any place on harness other than D-ring.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals, or other degrading elements. Inspection Prior to EACH use, inspect Cyclone Harness for deficiencies, including, but not limited to, corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, broken stitching, fraying, and missing or illegible labels.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 USA Safety Information ! WARNING Failure to understand and comply with safety regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. Do not misuse equipment.
www.guardianfall.com ET PE RFOR MANCE SA F NF Compliant with OSHA 1910, OSHA 1926 Subpart M, ANSI Z359.1-2007, and ANSI A10.32-2012. Capacity including tools: 130-420 lbs. GU A RDIA Size: Make only compatible connections: Dorsal D-ring for fall arrest attachment. □ SM □ S-M □ MED □ LG If present: Side D-rings for positioning only. Front Loop for use with ladder systems. Retrieval D-rings for rescue & retrieval.
