Product Name: WA-Anchor Part #: 00480; 00481 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards 1 Worker Classifications 1 Product Specific Applications 2 Limitations 2-3 Components and Specifications 4 Installation and Use 4 Maintenance, Cleaning, and Storage 5 Inspection 5 Inspection Log 5 Safety Information 6 Labels 7
Serial #: Trainer: User: Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1-2007, and ANSI A10.32-2012 standards for fall protection. Applicable standards and regulations depend on the type of work being done, and also might include state-specific regulations. Consult regulatory agencies for more information on fall protection systems and associated components.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Product Specific Applications ! WARNING Use of equipment in unintended applications may result in serious injury or death. Maximum 1 attachment per connection point. Personal Fall Arrest: WA-Anchor may be used to support a MAXIMUM 1 PFAS for use in Fall Arrest applications. Structure must withstand loads applied in the directions permitted by the system of at least 5,000 lbs.
Two connectors to same D-ring. NO. Connector directly to webbing. NO. Incompatible or irregular application, which may increase risk of roll-out. NO. Connector directly to horizontal lifeline. NO. Two or more snap hooks or carabiners connected to each other. NO. Correct Anchorage Positioning: This chart details allowable working zones required to reduce risk of swing falls and improper side loading. ALWAYS adhere to information specified by chart.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Components and Specifications Grade 8 Bolt and Nut Installation Location Materials: stainless steel. Fasteners: Grade 8 Bolt and Nut, and (4) 3½”, 16d Nails. Part # Length Description 00480 10½” WA-Anchor, Short 00481 13” WA-Anchor, Long Connection Point (4) Nail Installation Locations Installation and Use Minimum substrate requirements: Wood: 4”. Compatible roof pitch: 0/12 - 7/12.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals, or other degrading elements. Inspection Prior to EACH use, inspect WA-Anchor for deficiencies, including, but not limited to, corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, and missing or illegible labels. IMMEDIATELY remove WA-Anchor from service if defects or damage are found, or if exposed to forces of fall arrest.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Safety Information ! WARNING Failure to understand and comply with safety regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. Do not misuse equipment.
www.guardianfall.com 1-800-466-6385 www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Labels 6305 S. 231st St. Kent, WA 98032 WA-Anchor Part #: Date of Manufacture: Prior to use, read and understand all manufacturer's instructions provided with equipment at time of shipment from manufacturer. Compliant with OSHA 1910, OSHA 1926 Subpart M, ANSI Z359.1-07, and ANSI A10.32-12 regulations. Worker capacity range (including all equipment) is 130-420 lbs. Materials: stainless steel.
