Product Name: 4-Way Plate Anchor Part #: 00691 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards 1 Worker Classifications 1 Product Specific Applications 2 Limitations 2-3 Components and Specifications 4 Installation and Use 4-8 Maintenance, Cleaning, and Storage 9 Inspection 9 Inspection Log 9 Safety Information 10 Labels 11
This and any other included instructions must be made available to the user of the equipment. The user must understand how to safely and effectively use the 4-Way Plate Anchor, and all fall safety equipment used in combination with the 4-Way Plate Anchor. User Information Date of First Use: Serial #: Trainer: User: Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1-2007, and ANSI A10.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Product Specific Applications ! WARNING Use of equipment in unintended applications may result in serious injury or death. Maximum 1 attachment per connection point. Personal Fall Arrest: 4-Way Plate Anchor may be used to support a MAXIMUM 1 PFAS for use in Fall Arrest applications.
Two connectors to same D-ring. NO. Connector directly to webbing. NO. Incompatible or irregular application, which may increase risk of roll-out. NO. Connector directly to horizontal lifeline. NO. Two or more snap hooks or carabiners connected to each other. NO. Correct Anchorage Positioning: This chart details allowable working zones required to reduce risk of swing falls and improper side loading. ALWAYS adhere to information specified by chart.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Components and Specifications Materials: Powder-coated steel. Connection Point (20) 73/200” (.365”) wood/metal fastener installation locations (4) ½” Concrete fastener installation locations Installation and Use MINIMUM substrate requirements: Wood: 5/8” CDX or better. Metal: 24 gauge. Concrete: 6”. Prior to installation, plan your system: 1.
1. Use (20) #14-10 wood screws, or fasteners deemed compatible by a Competent Person, at all wood/metal fastener installation locations (see image on pg. 4). 2. All fasteners MUST be fully embedded in substrate. www.guardianfall.com Wood Installation: MINIMUM 5/8” thick CDX Metal Installation: 1. Use (20) #14-10, 2” metal screws, or fasteners deemed compatible by a Competent Person, at all wood/metal fastener installation locations (see image on pg. 4). 2.
www.guardianfall.com Concrete Installation: 1. Use (4) ½” concrete fastener installation locations (see image on pg. 4). Guardian Fall Protection recommends using ½“ x 3½” Threaded ROD assemblies. 2. Follow manufacturer’s fastener instructions for limitations and installation procedure. 4. DO apply torque (specific to fastener manufacturer specifications) to secure anchor to substrate. Compact washer to anchor surface.
HLLs used in combination with the 4-Way Plate Anchor MUST limit end anchor loads to 2,500 lbs. or less to maintain a 2:1 safety factor. When HLL is attached to Connection Point on 4-Way Plate Anchor, no other connections to the same anchor are permitted, with the exception of the continuation of the HLL system via the attachment of an additional cable run to a separate Connection Point. Multiple HLL spans MUST NEVER be connected to same Connection Point on the 4-Way Plate Anchor.
8 Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals, or other degrading elements. Inspection Prior to EACH use, inspect 4-Way Plate Anchor for deficiencies, including, but not limited to, corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, and missing or illegible labels.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Safety Information ! WARNING Failure to understand and comply with safety regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. Do not misuse equipment.
1-800-466-6385 www.guardianfall.com ! WARNING 90008 (Rev. C) Made in China Date of Manufacture: Part #: 00691 Prior to use, read and understand all manufacturer’s instructions provided with equipment. Compliant with OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1-2007, and ANSI A10.32-2012 regulations. Materials: powder-coated steel. Worker capacity: 130-310 lbs. (including all equipment), or up to 420 lbs. if used with equipment explicitly certified for such use.
