SDS

Australia Exposure Standards butane Butane 800 ppm / 1900 mg/m3 Not Available Not Available Not Available
Australia Exposure Standards naphtha petroleum, heavy, hydrotreated Oil mist, refined mineral 5 mg/m3 Not Available Not Available Not Available
EMERGENCY LIMITS
Ingredient Material name TEEL-1 TEEL-2 TEEL-3
butane Butane Not Available Not Available Not Available
propane Propane Not Available Not Available Not Available
naphtha petroleum, heavy,
hydrotreated
Naphtha, hydrotreated heavy; (Isopar L-rev 2) 350 mg/m3 1,800 mg/m3 40,000 mg/m3
methyltrimethoxysilane Methyltrimethoxysilane 38 mg/m3 410 mg/m3 2,500 mg/m3
titanium(IV) butoxide Tetrabutyl titanate; (Butyl titanate) 0.67 ppm 7.4 ppm 44 ppm
octamethylcyclotetrasiloxane Octamethylcyclotetrasiloxane 30 ppm 68 ppm 130 ppm
dimethoxydimethylsilane Dimethyldimethoxysilane 14 mg/m3 150 mg/m3 920 mg/m3
Ingredient Original IDLH Revised IDLH
butane Not Available 1,600 ppm
propane 2,100 ppm Not Available
naphtha petroleum, heavy,
hydrotreated
2,500 mg/m3 Not Available
methyltrimethoxysilane Not Available Not Available
octyltriethoxysilane Not Available Not Available
titanium(IV) butoxide Not Available Not Available
octamethylcyclotetrasiloxane Not Available Not Available
dimethoxydimethylsilane Not Available Not Available
Exposure controls
Appropriate engineering
controls
Articles or manufactured items, in their original condition, generally don't require engineering controls during handling or in normal use.
Exceptions may arise following extensive use and subsequent wear, during recycling or disposal operations where substances, found in the article, may be
released to the environment.
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed engineering controls can be
highly effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection.
The basic types of engineering controls are:
Process controls which involve changing the way a job activity or process is done to reduce the risk.
Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation that strategically "adds" and
"removes" air in the work environment.
Personal protection
Eye and face protection
Close fitting gas tight goggles
DO NOT wear contact lenses.
Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing the wearing
of lens or restrictions on use, should be created for each workplace or task. This should include a review of lens absorption and adsorption for the class
of chemicals in use and an account of injury experience. Medical and first-aid personnel should be trained in their removal and suitable equipment should
be readily available.
No special equipment for minor exposure i.e. when handling small quantities.
OTHERWISE: For potentially moderate or heavy exposures:
Safety glasses with side shields.
NOTE: Contact lenses pose a special hazard; soft lenses may absorb irritants and ALL lenses concentrate them.
No special equipment required due to the physical form of the product.
Safety glasses with side shields.
Chemical goggles.
Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing the wearing
of lenses or restrictions on use, should be created for each workplace or task.
Skin protection See Hand protection below
Hands/feet protection
Wear general protective gloves, eg. light weight rubber gloves.
NOTE:
The material may produce skin sensitisation in predisposed individuals. Care must be taken, when removing gloves and other protective equipment, to
avoid all possible skin contact.
Contaminated leather items, such as shoes, belts and watch-bands should be removed and destroyed.
No special equipment needed when handling small quantities.
OTHERWISE:
For potentially moderate exposures:
Wear general protective gloves, eg. light weight rubber gloves.
For potentially heavy exposures:
Wear chemical protective gloves, eg. PVC. and safety footwear.
Body protection See Other protection below
Other protection
The clothing worn by process operators insulated from earth may develop static charges far higher (up to 100 times) than the minimum ignition energies
for various flammable gas-air mixtures. This holds true for a wide range of clothing materials including cotton.
Avoid dangerous levels of charge by ensuring a low resistivity of the surface material worn outermost.
BRETHERICK: Handbook of Reactive Chemical Hazards.
No special equipment needed when handling small quantities.
OTHERWISE:
Chemwatch: 9-521064
Version No: 3.10
Page 4 of 10
GUARDSMAN WEATHER DEFENCE FABRIC PROTECTOR 284g AEROSOL
Issue Date: 15/03/2018
Print Date: 17/10/2018
Continued...