GUILD 130W 218 Piece Rotary Tool Kit PDM130DC.1 Instruction Manual After Sales Support UK/Ireland 0333 3201989 Help@guildpowertools.co.uk Important - Please read these instructions fully before operating or maintaining your Guild mini drill These instructions contain important information that will help you get the best from your Guild mini drill, ensuring it remains safe to operate.
Contents Safety Information.....................................................................................................3 In The Box.................................................................................................................10 Accessories..............................................................................................................10 Operating Instructions.............................................................................................
Safety Information Important - Please read these instructions fully before starting assembly Warning Symbols The following warning symbols appear throughout this assembly manual and indicate the appropriate safety measures you should take when assembling and operating the mini drill. To reduce the risk of injury, Please read the instruction manual Warning Wear ear protection Wear eye protection Wear dust mask Double insulation Waste electrical products must not be disposed of with household waste.
Safety Information Important - Please read these instructions fully before starting assembly General Power Tool Safety Warnings WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Safety Information Important - Please read these instructions fully before starting assembly General Power Tool Safety Warnings key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
Safety Information Important - Please read these instructions fully before starting assembly Safety instructions for all operations Safety Warnings common for grinding, sanding, wire brushing, polishing, carving or abrasive cutting-off operations: a) This power tool is intended to function as a grinder, sander, wire brush, polisher, carving or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
Safety Information Important - Please read these instructions fully before starting assembly Safety Warnings for battery pack in one hand and the tool in the other hand while in use. Clamping a small workpiece allows you to use your hand(s) to control the tool. Round material such as dowel rods, pipes or tubing have a tendency to roll while being cut, and may cause the bit to bind or jump toward you. m) Position the cord clear of the spinning accessory.
Safety Information Important - Please read these instructions fully before starting assembly Further safety instructions for all operations Feeding the tool in the wrong direction causes the cutting edge of the bit to climb out of the work and pull the tool in the direction of this feed. e) When using rotary files, cut-off wheels, high-speed cutters or tungsten carbide cutters, always have the work securely clamped. These wheels will grab if they become slightly canted in the groove, and can kickback.
Safety Information Important - Please read these instructions fully before starting assembly Safety Warnings Specific for Wire Brushing Operations a) Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin. b) Allow brushes to run at operating speed for at least one minute before using them.
In The Box Parts 1 Collet Nut 4 Speed selector 2 Spindle Lock Button 5 Hook 3 Carbon Brush Holder (on both sides) 6 On/Off switch Accessories 7 Collet (Ø1.6 mm x 1, Ø2.3 mm x 2, Ø3.2 mm x 3) 6 8 Polishing compound 1 (one in the tool, one in flexible shaft(28), four in the box) 9 Cut-off wheel (15/16” x 1/40” & 15/16” x 1/32”) 65 10 Sanding disk (180/320 grit) 72 11 Cutting wheel fixture (shank size: Ø3.
In The Box Parts 4 3 2 5 o 6 I 1 15 14 18 22 22 29 23 20 24 11 12 26 19 17 25 16 7 16 21 13 28 8 9 10 Customer Helpline 0333 3201989 27 11
Operating Instructions NOTE: Before using the tool, read the instruction book carefully. Intended Use This tool is intended for grinding, polishing metal as well as for cutting metal and drilling in metal and wood. 1. CHANGE THE COLLET (SEE FIG A) Three size of collets are provided to accommodate the different accessories shank sizes. When using an accessory with a smaller or larger shaft, you will need to change the collet which matches the shank size of the accessory as follows.
Operating Instructions A B 2 3. FITTING A CUTTING/SANDING WHEEL (SEE FIG D, E) he cutting wheel fixture (11) into the collet. Loosen the small screw (a)1on the 1First fit 7 cutting wheel fixture (11) with top of collet spanner (27). Insert the screw through the cutting wheel and then screw into the cutting wheel fixture (11). Do not over-tighten otherwise the wheel may crack. 4. ASSEMBLING THE FELT WHEEL (SEE FIG F) The felt wheel (22) is used with the screw drill (24).
E F Operating Instructions 5. FITTING THE SANDING ROLL (SEE FIG G1, G2, G3) To fit the sanding roll, firstly loosen the small screw on top of the hole for rubber wheel, this will allow the rubber to relax. Slide the sanding roll onto the holder. To secure, simply tighten the screw and the rubber roll will swell, gripping the sanding drum.
Operating Instructions G1 G3 H G2 6. CONNECT THE FLEXIBLE SHAFT TO THE TOOL (SEE FIG H) WARNING: Never bend the flexible shaft with a radius of less than 152mm when operating. Always store the flexible shaft carefully to avoid sharp bends when not in use. 1). Depress spindle lock button (2) and unscrew counter-clockwise the collet nut (1) and plastic ring (a) from the spindle. 2). Remove the collet from the spindle socket (b). 3).
G1 G2 Operating Instructions OPERATION 1. SWITCH ON / OFF (SEE FIG J) NOTE: This tool has been set to the slowest speed before switching on. To start the tool, press the on/off switch to “I” ON position. To stop, press the switch to “O” OFF position. G3 2. SPEED ADJUSTMENT (SEE FIG K) To achieve the best result when working with different materials, you can adjust the tool speed. It is adjustable from 10000 to 32000/min. The tool has a variable speed control for precise speed adjustment.
Using Accessories The chart below lists the description, use speed and scope for some of the small articles supplied together with the tool by category. To achieve best performance of the tool, it is strongly recommended that you read it prior to operation, failure to adhere to this may cause accessories to fail. NOTE: ALWAYS Wear eye protection Insert the shaft FULLY into the collet. Use ONLY up to the speeds stated below.
1 a Maintenance & Trouble Shooting J K WARNING: Remove the plug from the socket before carrying out any adjustment, servicing or maintenance. o REPLACING THE CARBON BRUSHES (SEE FIG L, M, N) The carbon brushes must be checked on a regular basis. There are two brushes in the tool and they must be replaced in pairs. Remove the carbon brush holders with the spanner and check the brushes. If the length of brush is less than 6mm, replace both brushes. Have the tool run at no load for 15 minutes.
Maintenance There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.
Technical Data Vibration Information Vibration total values (triax vector sum) determined according to EN 60745: Typical weighted vibration Vibration emission value: ah = 1.13m/s² Uncertainty K = 1.5m/s² The declared vibration total value may be used for comparing one tool with another, and may also be used in a preliminary assessment of exposure.
Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. Guarantee This product is selected for DOMESTIC USE ONLY and not for business use. This product is guaranteed against manufacturing defects for a period of 24 months.
Plug Replacement (Uk & Ireland Only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: Blue – Neutral Brown – Live As the colors of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured blue must be connected to the terminal which is marked with N.
