SAFE ● QUICK ● STRONG Owners Manual Models: GV2000 BioVault 6680 Surrey St Las Vegas, NV 897119 (800) 222-1055 -1- ● SMART
TABLE OF CONTENTS ● Warning and Recommendations ●● Congratulations on Your Purchase of a GunVault Safe 1) GunVault Safe Features and Functions……………………………………… Pg. 5 2) Getting Started ………………………………………………………………. Pg. 5 a) Securing Your Keys b) Locating the Battery Holder c) Installing the 9volt Battery d) Enrolling Your Personal Finger Print e) Close the Door and Practice f) Enrolling Additional Finger Prints 3) Mounting the Safe…………………………………………………………… Pg.
WARNINGS AND RECOMMENDATIONS Anything written in boldface type is a WARNING. Failure to observe these instructions constitutes a MISUSE of this product and may result in serious physical injury or DEATH. NO UNAUTHORIZED REPAIR GunVault safes are serviceable at the factory only. Any tampering, unauthorized repair and/or modification will void all warranties, and may cause the safe to fail unexpectedly, or be damaged. If in doubt, call GunVault technical support.
Congratulations on Your Purchase of a GunVault Safe! Your new GunVault Bio safe is a high quality product, which will give you years of service, backed up by excellent Technical Support and a strong Warranty. Before you get started reading this manual, please take a few moments to fill out your Warranty Registration Card and mail it in. Or register online at www.gunvault.com.
1. GunVault Safe Features and Functions Product Description and Features GunVault safes are manufactured from 16-gauge steel with pry-resistant doors and may be used to store a variety of items out of reach of children and other unauthorized persons.
Installing the 9volt Battery Position the safe with the door facing you, keypad upward. • Connect the power cable to the 9volt battery. You will hear a beep audio signal, confirming that power is connected. • Do not pinch the power cable. • Press the 9volt into position. • Press the foam ceiling back into your unit to cover the battery.
Enroll Additional Fingerprints • • • Open the GunVault by administrator’s fingerprint. Immediately after the door opens press and hold S1 button until 2 beeps sound. Place the new finger on the Fingerprint Reader, then press S1 button to activate the module, hold the finger on the reader until the Green light is on (it may need about 1-2 seconds). The new fingerprint is now enrolled.
a) Using the template provided, drill starter holes with drill bits appropriate for your installation. Drive screws only into the two key-slot holes. Drive the screws in until just enough room is left between the head of the screw and the mounting surface to permit you to slide the Vault’s key slots over the screws. b) Slide the Vault key-slots on over the screws. c) Now lift the foam padding in the bottom of the Vault and insert screws into remaining holes as desired, to retain the safe in place.
Warning: Never attempt to plug in a battery charger of any kind. Fire or explosion of batteries could result. Never use rechargeable batteries of any kind in a GunVault safe. Their power characteristics are not compatible with the safe. 7. Maintenance Low Battery Warning Indicator When the user opens the lock by enrolled fingerprint, if the Red light flashes and at the same time the beep sounds 3 times, it indicates low battery. Please replace the battery as soon as possible.
8. Frequently Asked Questions • I can’t program my GunVault. Disconnect the battery tray for 30 seconds and try to program again. • I hear a click when I enter my code. Replace your batteries (Duracell is recommended). • I hear a whirl noise when I try to open my GunVault. Please call Technical Support for assistance. • My new GunVault is missing the Battery Tray. The Battery Tray is pre-installed inside on the ceiling of the GunVault. Reach inside the unit and find the far end of the ceiling foam.
9. Technical Support If you have followed the above steps carefully and still have a problem operating your safe, phone GunVault Technical Support. Almost all problems can be solved within minutes over the telephone. Requirements for Return & Repair If possible, do not return your GunVault safe to your dealer. Instead please review Frequently Asked Questions (Page 13). If questions are not answered call GunVault Technical Support which can solve most problems over the telephone, making return unnecessary.
10. “Limited Warranty” 1. GunVault (the “Company”) warrants to the original consumer (the “Purchaser’) of any GunVault safe (the “GunVault safe”) purchased after January 1, 2014 against any damage caused by fire, burglary or attempted burglary for a period of five (5) years from the date of purchase. 2. The Company warrants to the purchaser that the GunVault safe will be free from defects in workmanship and materials for a period of one (1) year from the date of purchase. 3.
Inquiries or questions regarding GunVault safes should be directed to: Customer Support 800-222-1055 - 13 -