User's Manual

shutter release
Shutter release
extension cable
1 Package Contents
1. Locate the battery clip on the back of the remote.
2. Insert the battery.
2 Installing the Battery
Plug the remote cable into the remote and motor.
3 Connecting the remote and motor
2. Plug the shutter release cable into the remote
control and the camera’s remote control terminal.
Use the extension cable if more length is required.
+
=
Portable bag
Battery
Hook&Loop
Remote
4 Settings Menu：
Remote cable
1. Turn off power to reset the remote control.
2. Settings Menu
1/ Set the Language:
1. Press the up or down arrow and highlight the
Language menu option (P1).
2. Press the right or left arrow button to change
language between English and Chinese. Long
press the middle button to save your settings.
Set the start point:2/
1. Press the up or down arrow and
highlight the Settings menu option
(P2).
2. Press the middle button.
3. Highlight the Set Start option and
press the middle button (P3).
4. Press the right or left arrow button
to move the slider. Press the middle
button to stop the motion.
5. Press the middle button a second
time to select the start point (P4)
6. Long press the middle button to
save the start point.
Set the end point:3/
1. Highlight the Set End option and press the
middle button (P5)
2. Press the right or left arrow button to move
the slider. Press the middle button to stop the
motion.
3. Press the middle button a second time to
select the end point (P6)
4. Long press the middle button to save the
end point.
Motorized Slider
Following or Parallax Shot
The camera always points at the subject.
1. Loosen both left and right side adjusting rod brakes.
2. Move the camera base to the left side and adjust the
rod so that the camera points
at the subject.
3. Lock the left side rod brake.
4. Move the camera base to
the right side and adjust the
rod so that the camera points
at the subject.
5. Lock the right side rod brake.
Pan Shot
The camera pans with a maximum angle of 120°.
1. Loosen both left and right side adjusting rod brakes.
2. Move the camera base to
the left side and adjust the
rod so that the camera
points to the left side of the
subject.
3. Lock the left side rod brake
4. Move the camera base to
the right side and adjust the
rod so that the camera points
at the right side of the subject.
5. Lock the right side rod brake.
TROUBLE SHOOTING
1. Use a standard Sony NP-F550/F570/F770/F9XX
series battery.
2. Monitor the battery power level shown on the bottom
of the remote controller.
3. Make sure all cables are firmly inserted into all
devices.
4. If the slider is not horizontal, make sure to lock the
center brake before turning off the power or
disconnecting the cable. Under normal operations, the
motor acts as a brake and any loss of power will permit
the camera base to quickly fall to its lowest point
potentially damaging your camera or slider.
1. Locate the shutter release and extension
cable.
Using the time-lapse function
Camera shutter
release input
P3
P2
P4
Set St art
Set En d
Language:English
Reset:N o
Version: 1.0
Sett ing
Vide o Sho t
Tim e Lap se
Shutter s etu p
Sett ing
Set St art
Set En d
Language:English
Reset:N o
Version: 1.0
Sett ing
Speed:50%
Step :0
Set Sa rt: -33 554 432
Set St art
Set St art
Set En d
Language:English
Reset:N o
Version: 1.0
Sett ing
Pan-shot for Maximum angle 90°
Following shoot
Battery Charger
There are three photography methods available with
this slider. The Common Shot, the Following Shot and
the Pan Shot.
Common Shot
The camera angle does not change.
1. Loosen the adjusting rod
brakes on both ends and
center using the provided
scales.
2. Tighten the adjusting rod
on both ends.
5 Using the slider
Auto L oop
Auto S top
Auto M ode
Auto L oop
Auto S top
Auto M ode
P14
5. Auto Mode
Auto Mode has two options: Auto Loop and Auto Stop. To use
either one, you first must set the start and end points as
described in the Settings section.
1. Press the up or down arrow
and highlight the Video Shot
menu option. Then press the
middle button.
2. Press the up or down arrow
buttons and highlight the Auto
Mode menu option (P13).
Auto Loop will provide motion between the start and 1/
end points indefinitely.
1. Highlight the Auto Loop button and then
press the middle button (P14).
2. Press the right or left arrow to
start motion.
3. Press the middle button to
pause the motion.
Auto Stop will provide motion between the start and 2/
end points one time.
1. Highlight the Auto Stop button and then
press the middle button (P15).
2. Press the right or left arrow to start motion.
3. Press the middle button to pause the motion.
Common Shot
P7
P6
P4
P8
Speed:50%
Step :0
Set En d:- 335 54432
Set En d
Vide o Sho t
Tim e Lap se
Shutter s etu p
Sett ing
In t erva l：1 . 0
Tim e - l aps e : 1 . 0
Stop T ime：1 .2
Phot o：1 0 00
Auto L oop：No
Sett ing
Speed:50%
Step :0
Set Sa rt: -33 554 432
Set Start
P10
Vide o Sho t
Tim e Lap se
Shutter s etu p
Sett ing
Manual Mo de
Auto M ode
Sett ing
Set St art
Set En d
Language:English
Reset:N o
Version: 1.0
Sett ing
Spee d:50%
Dire ct io n:Pause
Manual Mo de
Vide o Sho t
Manual Mo de
Auto M ode
Sett ing
P13
P12
P15
4/ Set the speed:
1. At any time while setting the start or end
points, you can adjust the speed from
[1-100%] by pressing the Up or Down arrows
(P4), (P6).
Reset:5/
1.Highlight the Reset option(P7).
2.Press the right r left arrow button
to choose"Yes"or"No".Press the
middle button to reset the remote
control or go back setting menu.
3.Long press the middle button to
save the setting.
3. Time lapse menu
1/ Set the start point:
1. Press the up or down arrow and highlight the Time Lapse
menu option (P8).
2. Press the middle button.
3. Highlight the parameter you want to change
and adjust its value by pressing the right or left
arrow button (P9).
4. Press the middle button when complete.
5. Press the right or left arrow button to begin
time lapse shooting.
6. Press the middle button to pause any motion.
7. The minimum Interval time is 0.1 second, the
minimum Stop time is 1 second, and the Stop
time needs longer than Time-lapse time at least
0.2 seconds。
4. Video shot menu
1/ Manual Mode:
1. Press the up or down arrow and highlight
the Video Shot menu option (P10) and then
press the middle button.
2. Highlight Manual Mode and then press the
middle button(P11).
3. Press the left or right arrow button to begin
motion (P12).
4. You can adjust the speed at any time by
pressing the Up or Down arrow buttons.
P11
P9
P1
P5
P6
Speed:50%
Step :0
Set En d:- 335 544 32
Set En d
Add: 4301 N delaware ave unit D.Philadelphia. PA. 19137
Web: www.gvmled.com
MOTORIZED SLIDER
GP-80QD
GP-120QD
DC adapterDC adapterDC adapter
ShutterShutter
ReleaseRelease
Shutter
Release
MotorMotor
connectionconnection
Motor
connection