User Manual

MOTORIZED SLIDER
尺寸：198*210mm 1折2页
1. Please charge the battery before use the product.
2. Please install the battery on the controller as shown in
the picture. (As shown below)
Schematic diagram of mount
the battery
3. Connect the controller and slider as shown in the follo
wing pictures. (As shown below)
1 2
1
3
GT - 60D
4 5
3
4. Mounting the camera on the slider. (As shown below)
1 2
2 3
Power switchPower switchPower switch
5 Time-Lapse photography connect method :.
1）After finished above steps,
take out the shutter release cable
and extension cable. ( The cables
need to be purchased separately )
1 2
Shutter releaseShutter release
extension cableextension cable
Shutter release
extension cable
3 4
battery*1 battery charger*1
Carry bag*1
1
Packing list
2
Mounting the camera on the slider
Remote cable*1Remote controller*1
Interface of DC Interface of DC
power cablepower cable
Interface of DC
power cable
Interface of camera Interface of camera
shutter release cableshutter release cable
Interface of camera
shutter release cable
Interface of Interface of
controller controller
connect cableconnect cable
Interface of
controller
connect cable
Schematic diagram of charge
the battery
Shutter release
cable
Shutter release
extension cable
Shutter releaseShutter releaseShutter release
Camera shutter Camera shutter
release inputrelease input
Camera shutter
release input
P3
P2
P4
Set St art
Set En d
Lang uag e:Eng lish
Rese t:N o
Versi on: 1 .0
Sett ing
Video Sh ot
Tim e Lapse
Shut ter set up
Sett ing
Set St art
Set En d
Lang uag e:Eng lish
Rese t:N o
Versi on: 1 .0
Sett ing
Spee d:5 0%
Step :0
Set Sa rt:-3 355 4432
Set St art
Set St art
Set En d
Lang uag e:Eng lish
Rese t:N o
Versi on: 1 .0
Sett ing
P4
P8
Video Sh ot
Tim e Lapse
Shut ter set up
Sett ing
In t e rval：1.0
Time - l a p s e: 1.0
Stop T ime：1 . 2
Phot o：1 0 0 0
Auto L oop：No
Sett ing
Spee d:5 0%
Step :0
Set Sa rt:-3 355 4432
Set St art
P10
Video Sh ot
Tim e Lapse
Shut ter set up
Sett ing
Manu al Mode
Auto M ode
Sett ing
Set St art
Set En d
Lang uag e:Eng lish
Rese t:N o
Versi on: 1 .0
Sett ing
P11
P9
P1
P5
P6
Spee d:5 0%
Step :0
Set En d:-33 554 432
Set En d
Settings Menu
5/ Reset:
1.Highlight the Reset option(P7).
2.Press the right r left arrow button to choose
"Yes"or"No".Press the middle button to reset
the remote control or go back setting menu.
3.Long press the middle button to save the setting.
3. Time lapse menu
1/ Set the start point:
1. Press the up or down arrow and highlight
the Time Lapse menu option (P8).
2. Press the middle button.
3. Highlight the parameter you want to
change and adjust its value by pressing
the right or left arrow button (P9).
4. Press the middle button when complete.
5. Press the right or left arrow button to
begin time lapse shooting.
6. Press the middle button to pause any motion.
7. “Interval” means the slider moving time, the time unit
is “seconds”.
8. “Time-lapse” means the camera shutter shot time after
stop moving, the time unit is “seconds”.
9. “Stop time” means the time interval between the slider's
two movements, the time unit is “seconds”.
10. The minimum Interval time is 0.1 second, the
minimum Time-lapse time is 0.1 second, the minimum
stop time is 1 second. Note: the Stop Time needs longer
than the Time-lapse time at least 0.2 seconds.
4. Video shot menu
1/ Manual Mode:
1. Press the up or down arrow and highlight
the Video Shot menu option (P10) and then
press the middle button.
2. Highlight Manual Mode and
then press the middle button(P11).
3. Press the left or right arrow
button to begin motion (P12).
4. You can adjust the speed at any time by pressing the
Up or Down arrow buttons.
P7
Manu al Mode
Auto M ode
Sett ing
Spee d:50%
Dire ct ion: Pau se
Manu al Mode
Vide o Shot
1. Turn off power to reset the remote control.
2. Settings Menu
1/ Set the Language:
1. Press the up or down arrow and highlight
the Language menu option (P1).
2. Press the right or left arrow button to
change language between English and
Chinese. Long press the middle button to save your
settings.
Set the start point:2/
1. Press the up or down arrow
and highlight the Settings menu
option (P2).
2. Press the middle button.
3. Highlight the Set Start option
and press the middle button (P3).
4. Press the right or left arrow button to
move the slider. Press the middle button
to stop the motion.
5. Press the middle button a second time
to select the start point (P4)
6. Long press the middle button to save the start point.
Set the end point:3/
1. Highlight the Set End option and press
the middle button (P5)
2. Press the right or left arrow button to
move the slider. Press the middle button to
stop the motion.
3. Press the middle button a second time to
select the end point (P6)
4. Long press the middle button to save the
end point.
Set the speed:4/
1. At any time while setting the start or end
points, you can adjust the speed from [1-
100%] by pressing the Up or Down arrows
(P4), (P6).
5. Auto Mode
Auto Mode has two options: Auto Loop and Auto Stop.
To use either one, you first must set the start and end
points as described in the Settings section.
1. Press the up or down arrow and highlight the Video
Shot menu option. Then press the middle button.
2. Press the up or down arrow buttons and
highlight the Auto Mode menu option (P13).
Auto Loop will provide motion between 1/
the start and end points indefinitely.
1. Highlight the Auto Loop button and then
press the middle button (P14).
2. Press the right or left arrow to start motion.
3. Press the middle button to pause the
motion.
Auto Stop will provide motion between 2/
the start and end points one time.
1. Highlight the Auto Stop button and then
press the middle button (P15).
2. Press the right or left arrow to start motion.
3. Press the middle button to pause the motion.
TROUBLE SHOOTING
1. Use a standard Sony NP-F550/F570/F770/F9XX
series battery.
2. Monitor the battery power level shown on the bottom
of the remote controller.
3. Make sure all cables are firmly inserted into all
devices.
4. If the slider is not horizontal, make sure to lock the
center brake before turning off the power or
disconnecting the cable. Under normal operations, the
motor acts as a break and any loss of power will permit
the camera base to quickly fall to its lowest point
potentially damaging your camera or slider.
Auto L oop
Auto S top
Auto M ode
Auto L oop
Auto S top
Auto M ode
P14
P15
P13
2）Insert the cable into the controller's shutter release cable
interface (use the extension cable if needed) . Connect the
other side to the camera shutter release cable interface.
(As following pictures show)
P12