Compact Digital Storage Oscilloscope & Digital Multimeter GDS-200 & GDS-300 Series QUICK START GUIDE GW INSTEK PART NO.
This manual contains proprietary information, which is protected by copyright. All rights are reserved. No part of this manual may be photocopied, reproduced or translated to another language without prior written consent of Good Will Corporation. The information in this manual was correct at the time of printing. However, Good Will continues to improve its products and therefore reserves the right to change the specifications, equipment, and maintenance procedures at any time without notice.
SAFETY INSTRUCTIONS This section contains the basic safety symbols that may appear on the accompanying User Manual CD or on the instrument. For detailed safety instructions and precautions, please see the Safety Instructions chapter in the user manual CD. Safety Symbols These safety symbols may appear in the user manual or on the instrument. Warning Caution Warning: Identifies conditions or practices that could result in injury or loss of life.
Power Cord for the United Kingdom When using the instrument in the United Kingdom, make sure the power cord meets the following safety instructions. NOTE: This lead/appliance must only be wired by competent persons.
GETTING STARTED The Getting started chapter introduces the series lineup, main features, appearance, and set up procedure. Series Lineup There are 6 models in the series, divided by DSO bandwidth, DSO memory depth and DMM digit resolution. Model Name Bandwidth Memory DMM Temp. Depth Resolution Meas.
Features • Simultaneous DMM and DSO operation Portrait and landscape modes Large 800 x 480 TFT panel and capacitive touch panel 7.
Package Contents and Accessories Standard Accessories Item User Manual CD Quick Start Guide (this document) 100MHz passive probe; for GDS207 /307, GDS-210 /310 200MHz passive probe; for GDS220 /320 Multimeter test lead x2 Soft carrying case (large) Protection bag (small) Wrist strap Part Number 82DS-2200E01 82DS-22000M01 GTP-100A-4 GTP-200A-4 GTL-207 GSC-010 GSC-011 GWS-001 Optional Accessories Item Dual-channel differential probe, Only for GDS-200/300 Type A - Mini-B USB cable Vertical calibration cable
Panel Overview 1 3 2 CAT 1M W 300V 16.5pF 300Vrms MAX. 1 2 Digital Storage Oscilloscope GDS-220 200 MHz 1GSa/s 8 9 14 10 15 4 13 11 12 A mA COM 600mA MAX FUSED CAT II CAT III VW 600V 300V 10A MAX FUSED 5 6 7 16 Description 1. Channel 1 BNC input 2. Channel 2 BNC input 3. Tapped hole for options 4. 800 x 480 TFT screen, cap. touch panel 5. A and mA range DMM ports 6. Com port 7. Voltage, resistance and diode port 8. External power port for optional extras 9.
Display Overview 2 3 4 5 6 7 8 9 1 10 11 12 13 14 15 16 17 18 19 20 21 Note: Background color has been inverted for clarity. Description 1. Drop down menu 2. Trigger frequency 3. Trigger status 4. Date and Time 5. Memory bar 6. Horizontal position 7. Acquisition mode 8. Trigger level 9. Battery Indicator 10. Horizontal position indicator 11. Gesture control icon 12. Trigger level indicator 13. Channel indicators 14. Vertical scale 15. Horizontal scale 16. Trigger mode 17.
Setting up the Oscilloscope This section describes how to set up the oscilloscope properly including setting the stand, power up and basic touch gestures. Power Up Before the unit is powered up for the first time, it is recommended that the unit is first fully charged. 1. Plug the AC-DC power pack into the mains outlet. 2. Connect the 12V plug into the 12V socket on the interface panel. The unit will begin charging. An orange battery indicator light indicates charging, while green indicates charged. 3.
Tilting the Stand The GDS-200/300 has two adjustable tabs on the rear panel that can be used to position the instrument into two preset orientations. Horizontal Vertical Pull this catch Pull this catch Portrait and Landscape Mode 1. Tap the top of the screen to access the Menu tray. 2. Press the icon to toggle between horizontal and vertical view. Default Settings 1. Tap the top of the screen to access the Menu tray. 2. Press the icon to load the default settings.
Basic Operation This section will go over all of the basic touch gestures that are available using the default settings. Please see the user manual for comprehensive explanations. Channel/Ref/Math Waveform Selection To select the active waveform, tap the desired channel, math or reference indicator. When selected, the icon will become a solid triangle. Selected waveform Vertical Position of Selected Waveform Swipe the screen vertically to set the vertical position of the selected waveform.
Vertical Scale Pinch in/out vertically to set the vertical scale of the selected waveform. Scale Indicator Vertical Scale Horizontal Position and Scale Swipe the screen horizontally to set the horizontal position of the displayed waveforms. Pinch in/out horizontally to set the horizontal scale of the display.
Trigger Source and Trigger Level Tap on the trigger level indicator to toggle between trigger sources. Swipe the screen to the right of the grid to set the trigger level with the currently selected source. Toggle trigger source Trigger Level Drop Down Menu The Drop Down menu contains the Menu tray and the App tray.
SPECIFICATIONS The specifications apply when the oscilloscope is powered on for at least 30 minutes under +20°C-+30°C. Scope Specifications Vertical Channel Input Impedance Maximum Input Input Coupling Bandwidth Rise Time Sensitivity Accuracy Bandwidth Limit Polarity Offset Position Range Signal Acquisition Realtime Sample Rate Memory Depth Acquisition Mode Replay wfms. 2 (BNC-Shield) 1MΩ CATII 300VRMs AC, DC, GND DC-70/100/200MHz (-3dB) <5ns / 3.5ns / 1.75ns approx.
Trigger Source Trigger Mode Trigger Type Trigger Holdoff Coupling Sensitivity Horizontal Range Roll Pre-Trigger Post-Trigger Accuracy X-Y Mode Phase Shift Ch1 or Ch2 Auto, Normal, Single, Force Edge, Pulse width, Video, Alternative 10ns - 10s AC, DC, LFR, HFR, NR DC - 25MHz: approx. 0.5div or 5mV 25MHz - 70/100/200MHz: approx. 1.5div or 15mV 5ns-100s/Div (1-2-5 increments) 100ms/div - 100s/div 10 div max.
Miscellaneous Multi-language Menu On-line Help Time and Clock Battery Battery Power Charge Time Operation Time Interface USB Internal Flash Disk Display Type Display Resolution Display Orientation Backlight Control Touch Panel Power Adapter Line Voltage DC Output Available Available Available Li-polymer 6100mA/hr, 7.4V (Built-in) 2.0 hour (75%) 4.1 hours, depending on the operating conditions.
DMM Specifications Basic Reading Voltage Input DC Voltage Range Accuracy Input Impedance DC Current Range Accuracy AC Voltage Range Accuracy 50,000 counts, 4½ digits (GDS307/310/320) 3½ digits (GDS-207/210/220) CAT II 600VRMS, CAT III 300VRMS 50mV, 500mV, 5V, 50V, 500V, 1000V, 6 ranges GDS-307/310/320: 50mV, 500mV, 5V, 50V, 500V ±(0.05% + 5 digits), 1000V ±(0.1% + 5 digits) GDS-207/210/220: 50mV, 500mV, 5V, 50V, 500V, 1000V ±(0.
AC Current* Range Accuracy 50mA, 500mA, 10A 3 ranges 50mA, 500mA, ±(1.5% + 15 digits) at 50Hz-1kHz; 10A ±(3% + 15 digits) at 50Hz - 1kHz * Measure range: >10mA Resistance* Range 500Ω, 5kΩ, 50kΩ, 500kΩ, 5MΩ, 5 range Accuracy 500Ω, 5kΩ, 50kΩ, 500kΩ ±(0.3% + 3 digits); 5MΩ ± (0.5% + 5 digits) * Measure range: 50Ω to 5MΩ Diode Test Maximum forward voltage 1.5V, Open voltage 2.8V Temperature (Thermocouple)* Range -50°C - + 1000°C Resolution 0.
EC Declaration of Conformity We GOOD WILL INSTRUMENT CO., LTD. No.7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan GOOD WILL INSTRUMENT (SUZHOU) CO., LTD. No.
