Datasheet

Education Lab and Training Institution
Research & Design
Quality Assurance Verification
Full Measuring Functions with DUT V/I
Monitor
Wide Test Frequency 20Hz~10/5/1MHz
0.1% Basic Accuracy & 6 Digits
Measurement Resolution
Large LCD Display with Intuitive User
Interface
DC Resistance Measurement
Multi Step Mode
Graph Mode
Standard RS-232C / GPIB Interface
FEATURES
APPLICATIONS
Made to Measure
Since 1975
LCR-8000G Series
LCR-8000G Series
10MHz / 5MHz / 1MHz PRECISION LCR METER
The Smarter Way to Characterize Components
C.
The LCR-8000G Series LCR meter, with test frequency up to 10MHz, provides accuracy, versatility and high
resolution for a wide range of component measurements, even including DC resistance measurement and
Voltage/Current monitoring. The Multi-Step function allows on-screen programming of customized
measurement sequence with Pass/Fail indication. Each program includes 30 test steps and each test step can be
set with selected parameters and test limits. Under Multi-Step operation, a tedious work routine can be done
step by step automatically just at a press of a button. With Graph Mode, LCR-8110G, LCR-8105G and LCR-8101G
display the component impedance response either over a wide range of test frequency sweep or over a wide
range of test voltage sweep in a graph chart. This gives an analysis result of either impedance vs. frequency or
impedance vs. applied voltage all at a glance. GPIB and RS-232C interfaces are available as standard for
instrument control and test result display on the PC. The rich features of LCR-8000G Series easily make your
measurement tasks done at a very competitive price.
Pass/fail Function With Judgment Alarm
In the Pass/Fail test, primary parameter measurement
result is compared with user-defined limits and the
pass or fail result is then displayed. Three methods,
including absolute limit, percentage and delta limit,
are available for Hi(high) and Lo(low) limit setting
based on the nominal test value. The Pass/Fail test
checks whether the parameter measurement result
sits within the limits, then display "PASS" for within
the limits, or "LO" for lower than the low limit, or
"HI" For higher than the high limit. A scale and bar
for displaying measurement result is shown at the
center of the screen to give a graphical identification,
which greatly reduces operator's load in a long time
inspection work. This scale and bar also facilitate the
adjustment of the variable components. Either Pass
or Fail result can be set with a buzzer alarm, which
makes component or material sorting easy with
sound identification.
Wide Frequency Range With Friendly
Intuitive User Interface
The LCR-8000G Series is designed to perform precision
impedance measurements over a wide frequency range
of 20Hz ~ 10MHz for LCR-8110G, 20Hz ~ 5MHz for
LCR-8105G and 20Hz ~1MHz for LCR-8101G. The
instrument is capable of measuring 11 different
parameters with 0.1% basic accuracy, which meets the
precision measurement requirements of components
and modules used in the RF circuits. The large LCD
display with single-layer operation menu of LCR-8000G
Series provides users with ultimate convenience to
plug and play without much learning time.
C.
The graph function shows the component
characteristics in visual manner. Either voltage sweep
or frequency sweep can be selected for horizontal
scale. Just select the parameter, and set the start/stop
voltage or the start/stop frequency of the sweep, LCR
-8000G will run through the sequence of
measurements and show the results on a graph.
This graphical parameter measurement performs the
characteristic verification of components and
materials over the response to the changes in AC test
frequency or AC test voltage without the need of
complex programming of an external controller. When
the graph gets out of the vertical range, the LCR-
8000G Series can automatically adjust the scale to
get full test information. On the graph the marker
operation is available for detailed observation.
Graph Mode
The Multi-Step mode is capable of running a series of
measurements of a component at a number of user-
defined steps in sequence automatically. Total 64
programs can be saved into the non-volatile memory,
and each program contains up to 30 test steps. The
parameter and Hi/Lo limits can be set respectively for
each test step. After a program being properly edited,
the instrument can run through all the measurement
steps either at a press of the button under the Manual
Trigger selection, or automatically run the program by
detecting the connection of a DUT under the Auto
Trigger selection. When all the test steps are
completed, the screen shows the measurement
reading of the parameter being selected for each step
with Pass, HI, or LO measurement result.
Multi Step Mode
PASS/FAIL Function ( abs , % , )
with Judgment Alarm
Average 1 ~ 256 Times
CR-8000GGD1DH
ORDERING INFORMATION
Specifications subject to change without notice.
LCR-8110G
10 MHz Precision LCR Meter
LCR-8105G
5 MHz Precision LCR Meter
LCR-8101G
1 MHz Precision LCR Meter
STANDARD ACCESSORIES
User manual x 1
Power cord x 1
Test lead LCR-12 x 1
OPTIONAL ACCESSORIES SELECTION GUIDE
Brief Description
Accessory Model
LCR-8110G LCR-8105G LCR-8101G
LCR-05
LCR-06A
LCR-07
LCR-08
LCR-09
LCR-13
LCR-12
GTL-232
GRA-404
Test Fixture for axial & radial lead components
Test Lead with Kelvin clip (4 wire type)
Test Lead with Alligator clip (2 wire type)
Test Lead with Kelvin clip (4 wire type)
Test Fixture (Tweezers) for SMD/Chip components
Test Fixture for SMD/Chip components
Test Fixture for SMD/Chip components
RS-232C Cable
Rack Adapter Panel (19", 4U)
Note " " means the accessories work with a frequency limitation (under 1MHz)
LCR-06ALCR-05 LCR-07 LCR-08 LCR-09
LCR-13 LCR-12
Test Signal Level (rms)Test Frequency Step Accuracy
10mV ~ 2V3MHz 1mV/10mV 2% 5mV
10mV ~ 1V> 3MHz 1mV/10mV 2% 5mV
R, Z, X, Rdc
Mode
G, Y, B
L
C
D
Q
0.1m ~ 100M
Measure Range
10nS ~ 1000S
0.1nH ~ 100kH
0.01pF ~ 1F
0.00001 ~ 9.9999
0.1 ~ 9999.9
-180 ~ +180
TEST FREQUENCY
INPUT IMPEDANCE
BASIC ACCURACY
TEST SPEED
TEST SIGNAL LEVELS
SHORT CIRCUIT CURRENT
MEASUREMENT RANGES
MEASUREMENT PARAMETERS
SERIES OR PARALLEL EQUIVALENT CIRCUIT
SERIES EQUIVALENT CIRCUIT ONLY
PARALLEL EQUIVALENT CIRCUIT ONLY
POLAR FORM
LCD DISPLAY
INTERFACE
POWER SOURCE
DIMENSIONS & WEIGHT
20Hz ~ 1MHz/5MHz/10MHz, 5 Digits, 0.005%
100
0.1% (R, Z, X, G, Y, B, L, C)
AC (>2kHz)
MAX: 75mS
FAST: 150mS
MEDIUM: 450mS
SLOW: 600mS
DC
MAX: 30mS
FAST: 60mS
MEDIUM: 120mS
SLOW: 900mS
Max. 20mA
Impedance (Z), Phase Angle ( ), Inductance (L), Capacitance (C), AC Resistance (Rac), Quality Factor (Q),
Dissipation Factor (D), Admittance (Y), Conductance (G), Reactance (X), Susceptance (B), DC Resistance (Rdc)
C + R, C + D, C + Q, L + R, L + Q, L + D
X + R, X + D, X + Q
C + G, B + G, B + D, B + Q, B + R, L + G
Z + Phase Angle, Y + Phase Angle
320 x 240 DOT-MATRIX
RS-232C, GPIB
330(W) x 170(H) x 340(D)mm, Approx. 5kg
SPECIFICATIONS
AC 115V (+10%/-25%), AC 230V (+15% / -14%)(Selectable), 50/60Hz
AVERAGE
1 ~ 256 times
GOOD WILL INSTRUMENT CO., LTD.
Global Headquarters
No. 7-1, Jhongsing Road, Tucheng City, Taipei County 236, Taiwan
T [phone] F [phone]
E-mail: [e-mail]
China Subsidiary
E-mail: [e-mail]
U.S.A. Subsidiary
INSTEK AMERICA CORP.
3661 Walnut Avenue Chino, CA 91710, U.S.A.
T [phone] F [phone]
E-mail: [e-mail]
Japan Subsidiary
INSTEK JAPAN CORPORATION
4F, Prosper Bldg, 1-3-3 Iwamoto-Cho Chiyoda-Ku,
Tokyo 101-0032 Japan
T [phone] F [phone]
E-mail: [e-mail]
GOOD WILL INSTRUMENT (SUHZOU) CO., LTD.
NO. 69, Lushan Road, Snd, Suzhou Jiangsu 215011 China
T [phone] F [phone]
Malaysia Subsidiary
27, Persiaran Mahsuri 1/1, Sunway Tunas,
11900 Bayan Lepas, Penang, Malaysia
T [phone] F [phone]
E-mail: [e-mail]
GOOD WILL INSTRUMENT (M) SDN. BHD.
Korea Subsidiary
Room No.805, Ace Hightech-City B/D 1Dong,
Mullae-Dong 3Ga 55-20, Yeongduengpo-Gu, Seoul, Korea
T [phone] F [phone]
E-mail : [e-mail]
GOOD WILL INSTRUMENT KOREA CO., LTD.
www.gwinstek.com
Since 1975
Made to Measure
Simply Reliable
Our low TCO helps you control costs
with reliable products and services.