USER’S MANUAL Storage Cabinet THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Contact Us! Do NOT return this item. Contact our friendly customer service department for help first. E-mail product cs@gymaxservice.com Before You Start Read each step carefully before starting. It is very important to ensure each step followed in correct order, otherwise assembly difficulties may occur. Most of board parts are labeled or stamped on the raw edges. Have a check to make sure all parts are included. Work in a spacious area, preferably on a carpet close to where the unit will be used.
please contact us in time. 35mm Male Camlock x 12 1 Top Panel x 1 (30(w)cmx30(d)cm) 2 Left Side Panel x 1 (78.5(w)cmx28.4 (d)cm) 3 Female Camlock x 12 Right Side Panel x 1 (78.5(w)cmx28.4(d)cm) Magnetic Catch x 1 Catch Plate x 1 Hinge x 2 4 7 Bottom Panel x 1 (28(w)cmx21.5(d)cm) Door x 1 (51.4(w)cmx21.3(d)cm) 5 8 Fixed Shelf x 1 (28(w)cmx21.5(d)cm) Back Panel (74.3w)cmx23.5 (d)cm) 4 6 30mm Wooden Dowel x 12 14mm Screw x 2 10mm Screw x 9 Adjustable Shelf x 1 (26(w)cmx21.
N Inserting Male Camlocks Q F 1. Insert 12 x Male Camlocks A A into Panels 11 22 and 3 as shown. D 2. Connect Magnetic Catch D to Right Side Panel 33 D F as shown using 2 x Screw F. A A A A A 1 A The unit is floor standing, but it is recommended that the unit is secured to the wall. A 3 A A A 3. To the underside of Top Panel 1 , connect wall strap M as shown using 1 x Washer Q and screw N A 2 A 1 M Q N 1. Insert 8 x Dowels C B into the ends of Panels 44 and 5 as shown. 2.
1. Insert 4 x Dowels C into the top edge of Side Panels 22 and 3 as shown 1. Insert 4 x Shelf Supports LL into internal holes in Side Panels 22 and 33. 1 2. Locate Top Panel 1 into positon as shown. C 3. Insert 4 x Female Camlocks B B into Side Panels 22 and 33. Use a screwdriver to turn the Female Camlocks Clockwise to lock 2 C B 2. Locate Shelf 6 onto Supports as shown 2 C B 3 3 I For more information refer to the Using Camlocks Section L 4 6 1. Locate Back Panel 88 into position.
7 1. Connect Handle II to the Door using 2 x Screws JJ 2. Connect the Door to the unit by attaching the hinges to Side Panel 22 as shown using 2 x Screw H H per Hinge 2 H H 7 I J J 8 The unit is floor standing, but it is recommended that the unit is secured to the wall. P Q O 1. Move the unit into desired position. M 2. Mark the location of the fixing holes on the wall with a scribe. Warning: Before driling,check wall for hidden pipes and cables. 3. Drill hole and insert 1 x P wall plug D 4.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.