Operation Manual

ManualsBrandsGys ManualsBattery ChargerDHC 54 E MULTICHARGE STATION

SCM54E

SWITCHING POWER, DIGITAL PROCESSING

BATTERY BUS CHARGER/MAINTAINER

=================================================

Specification:

Charges------------------------ 12V SLI, AGM, Gel Batteries

Input-------------------------------------220~240VAC 2A 50HZ

Charging Output Mode--------------------------------5 AMPS

Maintenance Output Mode---------------------Pulse Charge

Leads-------------------------------------------------------183 CM

Size----------------------------------------35.0 X 19.0 X 7.5 CM

Weight------------------------------------------------------2.5KGS

- GB.1-V1 -

Summary of content (11 pages)

PAGE 1
SCM54E SWITCHING POWER, DIGITAL PROCESSING BATTERY BUS CHARGER/MAINTAINER ================================================= Specification: Charges------------------------ 12V SLI, AGM, Gel Batteries Input-------------------------------------220~240VAC 2A 50HZ Charging Output Mode--------------------------------5 AMPS Maintenance Output Mode---------------------Pulse Charge Leads-------------------------------------------------------183 CM Size----------------------------------------35.0 X 19.0 X 7.
PAGE 2
SCM54E SWITCHING POWER, DIGITAL PROCESSING BATTERY CHARGER/MAINTAINER IMPORTANT SAFETY INSTRUCTIONS： 1. SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for battery charger/maintainer Model SCM54E. 2. Use SCM54E only on 12 volts LEAD ACID, AGM and GELLED ELECTROLYTE (GEL-CELL) batteries. Do not attempt to use on other voltages and types of batteries (DRY CELL, NICKEL CADMIUM, NICKEL METAL HYDRIDE, etc.) commonly found in small home appliances.
PAGE 3
12. Place the power cords in a location where they will not be stepped on, tripped over, or subjected to stress or abuse of any kind. 13. For fuse replacement, contact distributors for replacement. Any tampering or incorrect assembly may result in fire or electric shock and voids the warranty. 14. Never attempt to charge a frozen battery. Allow the battery to return to room temperature before connection. Suggested operation range is in ambient temperature. 15.
PAGE 4
6. 7. 8. and water. If acid enters eye, immediately flood eye with running cold water for at least ten minutes and get medical attention immediately. NEVER smoke or allow a spark or flame in vicinity of battery or engine. Be extra cautious to reduce risk of dropping a metal tool onto the battery. It could spark or short-circuit the battery or other electrical parts and could cause an explosion.
PAGE 5
corrected before the battery is replaced after charging. CHARGER/MAINTAINER LOCATION: 1. Locate charger as far away from battery as DC cables permit. 2. Never place charger directly above battery being charged. Gases from battery will corrode and damage charger. 3. Never allow battery acid to drip on charger when reading gravity or filling battery. 4. Do not operate charger in a closed area or restrict ventilation in any way. 5. Do not set a battery on top of charger. SETTING UP & OPERATIONS: 1.
PAGE 6
8. When SCM54E is being used, it will show LED lights as follows: Green and red LED light both off: NO AC Power There is no AC power applied. Green light flashing only: Standby for charging batteries Before using, please check following: a. Are clamps properly connected to batteries? b. Is the battery voltage below 1 voltage? c. Is there any battery under charge? Green light on & red light flashing: Charging batteries SCM54E is charging the batteries.
PAGE 7
SCM54E is safely maintaining the battery at a full charge when the green light is on. The battery is ready. Simply remove the battery clamps and set them on the working surface clear from the other batteries and battery clamps. You can now load test the battery if necessary. ※ 1.When the battery clamps are accidentally disconnected while charging is in effect, the SCM54E will shut off. Green indicator light will go flashing. Simply reconnect the battery charged. 2.
PAGE 8
2. Why do we offer 5 Stage Charging? The voltage/current curve graph Desulphation Desulphation Fast Charge Equalization & Analysis Top Off Fast Charge Voltage Current Time - GB.
PAGE 9
1st Stage: Desulfation: Focused on deeply discharged or lightly sulfated batteries, which show low voltage and are hard to activate. The SCM54E Charger will start the charge pulse to charge the battery until the voltage recovers & reaches expected rechargeable level. The purpose of this stage is to save an over-discharged or a lightly sulfated battery for recovery. 2nd Stage: Fast Charge: When the voltage of the battery is above the set level.
PAGE 10
FAST CHARGE TIME Battery Size 5 Amp Time to 75% Charge (Ah) (h) 10 2 14 2-3 20 4 50 10 90 18 120 24 150 30 200 40 3. Other advantages of SCM54E Charge Energy Saving: The SCM54E Charger provides True Pure DC current Charging capacity which reduce power consumption in charging process & save up to 20% energy compared to conventional chargers. Time Saving: Switching mode technology charges battery at least 1.5 times faster than units using conventional technology.
PAGE 11
TERMS AND CONDITIONS OF WARRANTY Any battery charger defective in material or workmanship will be repaired or replaced according to published defective return test repair procedures. The existence of a defect shall be determined by the seller in accordance with published procedures. The published test procedures are available upon request.