Technical Specifications

H&C Products Group Technical Service 1.800.867.8246 Page 1 of 1
101 W. Prospect Avenue www.hcconcrete.com
Rev. 10/17
Cleveland, Ohio 44115 PDS ID: 111.322
PRODUCT DESCRIPTION
H&C® SHARKGRIP® Slip-Resistant Additive is a micronized
polymer for addition to H&C coatings for slip resistance, fine
texturing, and gloss reduction. Due to its low oil absorption
and high solvent resistance, it will stir easily into most oil-
based and latex-based paints and other coatings
with minimal effect on the coating’s viscosity. Its low density
allows it to stay well suspended in thin materials such
as stains.
FEATURES & BENEFITS
• Add to latex-based and oil-based coatings, stains and sealers
• Spherical-shaped particles provide easier cleanibility and are
smooth to the touch
RECOMMENDED USES
H&C® SHARKGRIP® Slip-Resistant Additive is formulated for
use on concrete and masonry surfaces including inclinded
Surfaces, Driveways, Garages, Steps, Patios and Pool Decks.
JOBSITE TEST SECTION
Due to the wide variety of substrates, preparation methods,
application methods and environments, it is important to test
the product in an inconspicuous spot for adhesion and
compatibility prior to full-scale application.
LIMITATIONS
H&C® SHARKGRIP® Slip-Resistant Additive will increase the
coefficient of friction on the coated surface, but due to its
small particle size, the coating that this is added to should be
considered slip-resistant but not non-skid.
Not for use with wood stains.
INSTRUCTIONS
Add contents of one 3.2 oz container into one gallon of H&C®
Concrete Stain or Sealer. H&C® SHARKGRIP® Slip-Resistant
Additive should be mixed into the final topcoat. Mix well and
apply with a roller.
*Refer to Stain or Sealer label and data page for detailed
product guidelines.
PHYSICAL PROPERTIES
Physical Properties and Characteristics
Property
Test Method
Value
Melting Point ASTM D127 330-335°F
ORDERING INFORMATION
Clear
3.2 OZ
16 OZ
19 lb.
Part Number/SMIS
50.155004-16/ 6507-12276
50.155005-20/ 6507-12284
50.155008-99/ 6507-12292
TECHNICAL SERVICES
The information and recommendations set forth in this product
data sheet are based on tests conducted by or on behalf of
H&C Products Group and The Sherwin-Williams® Company.
Such information and recommendations set forth herein are
subject to change and pertain to the product offered at the
time of publication. Consult your H&C or Sherwin-Williams
representative to obtain the most recent product data sheet.
For technical assistance, call 1-800-867-8246 or visit
www.hcconcrete.com.
CAUTION
CAUTIONS Use only with adequate ventilation. To avoid
overexposure, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches, or dizziness,
increase fresh air, or wear respiratory protection (NIOSH
approved) or leave the area.
FIRST AID: In case of eye contact, flush thoroughly with large
amounts of water. Get medical attention if irritation persists. If
swallowed, call Poison Control Center, hospital emergency
room or physician immediately. DO NOT TAKE INTERNALLY.
KEEP OUT OF THE REACH OF CHILDREN.
LIMITED WARRANTY
Seller’s and manufacturer’s only obligations shall be to replace
such quantity of product proved to be defective. Neither seller
nor manufacturer shall be liable for any injury, loss or damage,
direct or consequential, arising from the applicator’s inability to
use the product for his/her intended use. The user assumes all
risk and liability.
H&C® SHARKGRIP®
SLIP-RESISTANT ADDITIVE
•
Improves slip-resistance on concrete surfaces
•
Does not effect the color the top coat