SAFETY DATA SHEET 50.15501- Section 1. Identification Product name : H&C® CLEARPROTECT™ Solvent Based Cure and Seal Product code : 50.15501- Other means of : Not available. identification Product type : Liquid. Relevant identified uses of the substance or mixture and uses advised against Paint or paint related material. Manufacturer : H&C Products Group 101 W.
Section 2. Hazards identification General Prevention Response Storage Disposal Supplemental label elements Hazards not otherwise classified : Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. : Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves. Wear eye or face protection. Wear protective clothing.
Section 4. First aid measures Description of necessary first aid measures Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention. : Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Section 5. Fire-fighting measures Extinguishing media Suitable extinguishing media : Use dry chemical, CO₂, water spray (fog) or foam. Unsuitable extinguishing media : Do not use water jet. Specific hazards arising from the chemical Hazardous thermal decomposition products Special protective actions for fire-fighters Special protective equipment for fire-fighters : Highly flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard.
Section 7. Handling and storage Precautions for safe handling Protective measures : Put on appropriate personal protective equipment (see Section 8). Avoid exposure obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist. Do not swallow. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate.
Section 8. Exposure controls/personal protection 1,2,3-Trimethylbenzene 526-73-8 Xylene, mixed isomers 1330-20-7 ACGIH TLV (United States, 3/2019). TWA: 25 ppm 8 hours. TWA: 123 mg/m³ 8 hours. NIOSH REL (United States, 10/2016). TWA: 25 ppm 10 hours. TWA: 125 mg/m³ 10 hours. ACGIH TLV (United States, 3/2019). TWA: 100 ppm 8 hours. TWA: 434 mg/m³ 8 hours. STEL: 150 ppm 15 minutes. STEL: 651 mg/m³ 15 minutes. OSHA PEL (United States, 5/2018). TWA: 100 ppm 8 hours. TWA: 435 mg/m³ 8 hours.
Section 8. Exposure controls/personal protection Xylene 1330-20-7 CA Quebec Provincial (Canada, 1/2014). TWAEV: 50 ppm 8 hours. TWAEV: 246 mg/m³ 8 hours. CA Saskatchewan Provincial (Canada, 7/2013). STEL: 74 ppm 15 minutes. TWA: 50 ppm 8 hours. CA Alberta Provincial (Canada, 6/2018). 8 hrs OEL: 100 ppm 8 hours. 15 min OEL: 651 mg/m³ 15 minutes. 15 min OEL: 150 ppm 15 minutes. 8 hrs OEL: 434 mg/m³ 8 hours. CA British Columbia Provincial (Canada, 5/2019). TWA: 100 ppm 8 hours. STEL: 150 ppm 15 minutes.
Section 8. Exposure controls/personal protection Skin protection Hand protection Body protection Other skin protection Respiratory protection : Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties.
Section 10. Stability and reactivity Reactivity : No specific test data related to reactivity available for this product or its ingredients. Chemical stability : The product is stable. Possibility of hazardous reactions : Under normal conditions of storage and use, hazardous reactions will not occur. Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat or sources of ignition.
Section 11. Toxicological information Skin - Moderate irritant Rabbit mg 100 % - - Sensitization Not available. Mutagenicity Not available. Carcinogenicity Not available. Classification Product/ingredient name OSHA IARC NTP Cumene Xylene, mixed isomers - 2B 3 Reasonably anticipated to be a human carcinogen. - Reproductive toxicity Not available. Teratogenicity Not available.
Section 11. Toxicological information Information on the likely routes of exposure : Not available. Potential acute health effects Eye contact : Causes serious eye irritation. Inhalation : No known significant effects or critical hazards. Skin contact Ingestion : No known significant effects or critical hazards. : May be fatal if swallowed and enters airways.
Section 12.
Section 13. Disposal considerations inside the container. Do not cut, weld or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Section 14.
Section 15. Regulatory information SARA 313 SARA 313 (40 CFR 372.45) supplier notification can be found on the Environmental Data Sheet. California Prop. 65 WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. International regulations International lists : Australia inventory (AICS): Not determined. China inventory (IECSC): Not determined. Japan inventory (ENCS): Not determined. Japan inventory (ISHL): Not determined.
Section 16. Other information Key to abbreviations : ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978.
