Technical Specifications

ManualsBrandsH&C ManualsConcrete & Blacktop SealersWet Look High Gloss Clear Solvent-Based Concrete Sealer - 1 gal.

H&C Products Group Technical Service 1.800.867.8246 Page 1 of 3

101 Prospect Avenue www.hcconcrete.com

Rev. 6/15

Cleveland, Ohio 44115 PDS ID: 71.000012

PRODUCT DESCRIPTION

H&C® Wet Look High Gloss Sealer is designed to add deep

penetrating protection to exterior concrete such as driveways,

patios, walkways, garage floors and masonry walls. Designed

for use over bare concrete or previously stained concrete. This

wet look clear protects against UV rays, water seepage and

common chemicals.

FEATURES & BENEFITS

• Seals and protects to extend the life of concrete and

masonry surfaces.

• Imparts a beautiful high-gloss finish.

• Won’t peel, fade, or yellow over time.

• Resists damage from salt, UV rays oil, acids, pool chemicals

and heavy traffic.

RECOMMENDED USES

H&C® Wet Look High Gloss Sealer is formulated for use on

exterior concrete and masonry surfaces including driveways,

walkways, patios, pool decks, garage floors, and block and

stucco walls.

COVERAGE RATES

Substrate sq ft/gal

Concrete floors 200-250

Porous concrete 150-200

Concrete block 125-150

Split-faced block 100-125

Fluted block 75-100

Brick (clay) 100-150

JOBSITE TEST SECTION

Due to the wide variety of substrates, preparation methods,

application methods and environments, it is important to test

the product in an inconspicuous spot for adhesion and

compatibility prior to full-scale application.

LIMITATIONS

Only use on interior surfaces, such as garage floors, if the area

allows for good ventilation. Strong solvents, such as gasoline

or brake fluid, will dull the cured film. Do not use on wood

surfaces.

SURFACE PREPARATION

Bare Concrete: Newly poured concrete must be at least 28

days old. All concrete should be clean, dry and free of laitance,

grease, oil, paint and sealers. A high pressure water wash is

recommended. * To remove light soil from the surface, use a

cleaner degreaser mixed to a 50/50 ratio with water. To

remove heavy oil and grease stains, use the cleaner full

strength. Before applying product, all horizontal concrete

surfaces must be etched first with an etching solution or

muriatic acid, following label directions. For very smooth

troweled surfaces with no porosity, use etching solution at full

strength. For smooth-troweled concrete with some porosity,

use 1 part etching solution to 2 parts water. DO NOT ETCH

PAINTED SURFACES. If mold, mildew or fungus is present, kill

and remove with a solution of one cup household bleach to

one gallon of water. Wear protective eyewear, waterproof

gloves, and protective clothing. Quickly wash off any of the

mixture that comes in contact with your skin. Do not add

detergents or ammonia to the bleach/water solution.

Prepared concrete should have a pH level of 6 to 10. Allow to

dry 24 hours before sealing.

*WARNING: Removal of old paint by sanding, scraping or other means may

generate dust or fumes that contain lead. To avoid exposure to lead dust,

wear proper protective equipment, such as a properly fitted respirator (NIOSH

approved) and follow proper containment and cleanup procedures. For more

information, call the National Lead Information Center at 1-800-424-LEAD (in

U.S.) or contact your local health authority.

Repair: For the best waterproofing protection on vertical and

horizontal concrete and masonry surfaces, use a patch and

repair to address spalled concrete. Please note that patching

compounds will generally be visible through clear coatings.

H&C® Wet Look

High Gloss Sealer

• Durable high gloss finish

• Seals and protects cement surfaces

• Waterproofs and helps prevent stain damage

• Suitable for driving surfaces

Summary of content (3 pages)

PAGE 1
• • • • PRODUCT DESCRIPTION H&C® Wet Look High Gloss Sealer is designed to add deep penetrating protection to exterior concrete such as driveways, patios, walkways, garage floors and masonry walls. Designed for use over bare concrete or previously stained concrete. This wet look clear protects against UV rays, water seepage and common chemicals. FEATURES & BENEFITS • Seals and protects to extend the life of concrete and masonry surfaces. • Imparts a beautiful high-gloss finish.
PAGE 2
TOOLS REQUIRED • Natural bristle brush • Lamb’s wool or synthetic roller (3/8 inch nap) • Airless sprayer (pressure 500 to 1000 psi; tip .011 to .013 inch) APPLICATION INSTRUCTIONS Wait at least 24 hours after washing surface or after rain before applying H&C® Wet Look High Gloss Sealer. Only apply under dry conditions. Air and concrete surface temperatures should be above 50°F and below 95°F for 24 hours following application. How to Apply: Stir thoroughly before and during application.
PAGE 3
CAUTION CAUTIONS: CONTAINS VOLATILE ORGANIC COMPOUNDS. Contents are FLAMMABLE. Vapors may cause fl ash fires. Keep away from heat, sparks, and open flame. During use and until all vapors are gone: Keep area ventilated - Do not smokeExtinguish all flames, pilot lights, and heaters - Turn off stoves, electric tools and appliances, and any other sources of ignition. VAPOR HARMFUL. Use only with adequate ventilation.