Technical Specifications

H&C Products Group Technical Service 1.800.867.8246 Page 1 of 3
101 W.Prospect Avenue www.hcconcrete.com
Rev. 6/15
Cleveland, Ohio 44115 PDS ID: 72.000010
PRODUCT DESCRIPTION
H&C® Concrete Solid Stain is a water-based stain designed to
add deep penetrating protection and long-lasting beauty for
both exterior and interior concrete. Available in 2 pre-
packaged and a variety of tintable colors. It may be applied to
bare concrete or previously painted surfaces and is highly
resistant to pool chemicals.
FEATURES & BENEFITS
• Highly resistant to pool chemicals.
• Will not peel, flake, or fade over time.
• Resists acids, ultraviolet rays, oil, gas and alkalis while
maintaining a decorative finish.
• Makes surfaces easier to clean.
• Ideal for high-pH surfaces.
RECOMMENDED USES
H&C® Concrete Solid Stain is formulated for use on concrete,
masonry and asphalt. It can be used on both interior and
exterior surfaces including walkways, patios, pool decks,
basement floors, and block and stucco walls.
COVERAGE RATES
Substrate* sq ft/gal
Concrete floors 200-300
Porous concrete 150-250
Concrete block 100-150
Split-faced block 75-125
Fluted block 50-100
Brick (clay) 100-150
Asphalt 200-250
*Coverage will vary depending on the porosity and texture of the substrate.
JOBSITE TEST SECTION
Due to the wide variety of substrates, preparation methods,
application methods and environments, it is important to test
the product in an inconspicuous spot for adhesion and
compatibility prior to full-scale application.
LIMITATIONS
Do not use on wood surfaces.
SURFACE PREPARATION
New Concrete: Allow new concrete to cure at least 28 days. All
horizontal concrete surfaces must be etched with H&C Etching
Solution or muriatic acid, following label directions. After
proper etching, the surface should feel like 120-grit sandpaper.
If not, then etch again. Vertical concrete surfaces should be
able to absorb water. To test absorption, spray various
sections of the surface to be stained with water. If the water
does not absorb rapidly, then acid etch the surface using an
etching solution, following label instructions, or use
mechanical abrasion methods. Do not apply the stain until all
surfaces are porous. Allow all surfaces to dry at least 24 hours
before staining. Prepared concrete must have a pH of 6 to 10.
Existing and Previously Painted Concrete: All concrete must
be porous, clean, dry and free of grease, oil and other
contaminates.
To spot clean, use a cleaner degreaser,
following label directions. If mold, mildew, or fungus is
present, kill and remove with a solution of 1 cup household
bleach to 1 gallon of water. Wear protective eyewear,
waterproof gloves, and protective clothing. Quickly wash off
any of the mixture that comes in contact with your skin. Do
not add detergents or ammonia to the bleach/water solution.If
surface has been previously painted, remove all old, peeling,
flaking paint by rough sanding to ensure adhesion of H&C®
Concrete Solid Stain. Rinse away sanding dust before stain
application.* DO NOT ETCH PREVIOUSLY PAINTED SURFACES.
*WARNING: Removal of old paint by sanding, scraping or other means may
generate dust or fumes that contain lead. To avoid exposure to lead dust,
wear proper protective equipment, such as a properly fitted respirator (NIOSH
approved) and follow proper containment and cleanup procedures. For more
information, call the National Lead Information Center at 1-800-424-LEAD (in
U.S.) or contact your local health authority.
Asphalt: Asphalt surfaces must be free of grease, oil, dirt, wax,
and other surface contaminates. Scrub with a solvent-free
cleaner, following label directions. Do not etch asphalt. Not
recommended for use on freshly sealed asphalt.
Repair: For the best waterproofing protection on vertical and
horizontal concrete and masonry surfaces, use a patch and
repair to address spalled concrete. Please note that patching
compounds will generally be visible through clear coatings
H&C® Concrete Solid Stain
• Interior & exterior use
• Penetrates, seals and protects
• Helps prevent water and chemical damage
• Resists fading, provides UV protection
• Easy application and clean up