w w w . H 2 O A u d i o . c o m Deep Dive Waterproof Case & Speakers Depth Rating 300ft/90m For updated manuals please visit our web site www.h2oaudio.
O-ring Mask Clip Speaker Lanyard Hole ® iPod Control Buttons Insert Holes & Height Adjuster Holes LED lights Battery Cover Cam Knob Depth Rating 300ft / 90m Connector Cable Cam Knob Lock 1 2
Quickstart: Instructions: I. Read “Getting Familiar with the iDive 300” I. Getting Familiar with the iDive300 Before using the iDive300 for the first time, it is highly recommended that you become familiar with opening and closing the case to ensure the case is sealed properly during use. To verify that you have sealed the case properly we recommend that you test the product without an iPod inside before initial use. Please follow the instructions below: II. Unlock and open case III.
IT IS EXTREMELY IMPORTANT YOU ENSURE THE O-RING IS PROPERLY SEATED IN ITS TRACK AND IS FREE OF DEBRIS BEFORE EACH USE. FAILURE TO DO SO MAY CAUSE DAMAGE TO OR DESTROY YOUR IPOD. Prior to use verify: 1. The O-ring is lightly lubricated and seated within the track in the lid. 2. The O-ring and contact surface are free of scratches and other imperfections. Do NOT use if: 1. The O-ring is dry, cracked, twisted, and/or out of alignment. 2.
To Close Case 1. Close lid 2. Rotate the cam knob clockwise 180° 3. Close the cam knob lock IV. Install batteries 1. Open case. 2. Disconnect and remove iPod from case if installed. 3. Turn the battery cover screw counter-clockwise until the screw loses contact with the insert plate. 4. Remove battery cover. 5. Install 3 AA batteries in the battery compartment. Make sure the positive and negative ends of the battery are oriented per the inscribed markings in the case. 6. Reinstall and close battery cover.
Included insert and height adjusters Insert and height adjuster reference A 1 Inserts and height adjusters are labeled to aid identification.
Power On/Off Press and hold the power button for 2 seconds to turn the iDive300 on/off. VI. Insert iPod 1. Ensure the correct inserts and height adjusters are installed for your iPod (PLEASE NOTE: If the correct insert and height adjusters are not used you may damage or destroy your iPod and the iDive300) 2. Place iPod in the inserts with the iPod dock connector facing toward the cam knob. 3. Insert the connector cable into the dock connector of the iPod with the H2O Audio logo facing up. 4.
In case of a Steady Red LED 1. Ensure you are using a supported iPod model. 2. Ensure the iPod is fully charged. 3. Ensure the iPod is turned on. 4. Disconnect & reconnect the connector cable. In case of a Flashing Red LED 1. Batteries of the iDive300 case are running low – change or recharge them soon. For Mask Strap Mounting: To Remove Mask Clip: Feed mask strap through the slits in each slot of the clip.
CAUTION: Do not store case in the following environments: * Solvents or other chemical fumes * High humidity * High Ozone * Extreme temperature fluctuations Storing the case in these conditions may lead to a damaged case, causing it to leak. Rinse the EXTERIOR of the system in fresh water after EACH use: 1. Make sure the case is securely closed. 2. Soak in clean fresh water for 30 minutes. 3. Rinse the entire system with freshwater. 4.
Improper use of this system may cause the user to make mistakes or decisions that may lead to serious injury or death. Important warning and disclosure: Any individual intending to utilize this product during S.C.U.B.A diving activities must be properly trained and certified by an accredited agency. Further, it is recommended that all divers stay within recreational dive limits and follow all safety stop considerations.
To Obtain Service: Please go to support section of our website or contact customer support at Customer Support Hours and Contact Information: Monday through Friday 9AM to 5PM PT Tel: 858.623.0339 Toll Free: 800-708-6080 support@h2oaudio.com PLEASE NOTE: No service returns will be accepted without a pre-return authorization RA#, which must be clearly marked on the outside of the package. The product will be returned COD if submitted without an RA#.
Q: Why is the Red LED flashing? A: The iDive300 is designed to measure battery-life of the 3-AA batteries that are used to power the “Made for iPod” connection electronics and the power amplifier. The Red LED will start to flash when the batteries have approximately 25% charge remaining. Note, the battery indicator of the iPod does not reflect the power remaining in the 3-AA batteries.
w w w . H 2 O A u d i o . c o m 11010 Roselle St. Suite 150, San Diego CA, 92121 Phone: 1.800.708.6080 or 858.623.0339 Email: support@h2oaudio.com Copyright Notice: This owner’s manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied, photocopied, reproduced, translated, or formed into any electronic format without prior consent in writing. H2O Audio is a registered trademark of H2O Audio, Inc. Apple and iPod are registered trademarks of Apple Inc.