Atlas - Single Robe Carcass Assembly Instructions - Please keep for future reference 152/9432 157/2537 157/9107 Dimensions Width - 50cm Depth - 59.5cm Height - 212.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 34kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you have damaged or missing components, call the Customer Helpline: 08456 400800 quoting the reference numbers below Please check you have all the panels listed below 2 Top/Base (D2399A) (500 x 592mm) x 2 3 Fixed Shelf (D2401A) (468 x 590mm) 1 Universal End (D2396A) (2074 x 591mm) x 2 4 Hanging Rail (FHR460) (460mm long) x 2 5 Back (X2100-494) (2100 x 494mm) 2
If you have damaged or missing components, call the Customer Helpline: 08456 400800 quoting the reference Components - Fittings numbers below Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions If you have damaged or missing components, call the Customer Helpline: 08456 400800 quoting the reference numbers below Step 1 The fixed shelf will need to go here if you are fitting the following:- Are you fitting 1 or 2 Hanging Rails or, an Internal Chest or, a Shelf Pack? The fixed shelf will need to go here if you are fitting the following:- Only 1 Hanging Rail or An Internal Chest or A Shelf Pack 2 Hanging Rails Follow Steps 2 and 3.
Assembly Instructions Step 3 Prepare the right end Refer to step 1 and, if you have chosen to fit 1 hanging rail or, an internal chest or, a shelf pack, screw 2 metal dowels B into the right end 1 . Only follow Steps 2 and 3 if you are only fitting 1 hanging rail or, an internal chest or, a shelf pack. If you are fitting 2 hanging rails, follow Step 4 and 5. B Note: If you have purchased a shelf pack, do not fit the rail holder. K Note: Tighten the metal dowels up fully against the panels.
Assembly Instructions Step 5 Prepare the right end Only follow Steps 4 and 5 if you are fitting 2 hanging rails. If you are just fitting 1 rail, follow Step 2 and 3. J Refer to step 1 and, if you have chosen to fit 2 hanging rails, screw 2 metal dowels B into the right end 1 . J B K K Note: Tighten the metal dowels up fully against the panels. K B To fit the 2 rail holders K screw through the top hole with screw J and into the shallow mark hole drilled in the right end 1 .
Assembly Instructions Step 7 Join the fixed shelf to the right side If you have fitted the 2 metal dowels in this position, the fixed shelf will go here. Push the fixed shelf 3 onto the right side 1 . Use a screwdriver to tighten the 2 large locking nuts C fitted to the fixed shelf 3 . Note: Turn the large locking nuts C as far as they will go - more than 1/2 a turn. 3 1 Finished front edge Finished front edge B C The following diagrams will show the fixed shelf at the top end of the unit.
Assembly Instructions Step 9 G Prepare the base Note: Use the shallow mark holes to fit the feet. M Screw the 4 feet M into the shallow mark holes on the base 2 using screws G . M M 2 M Finished front edge Step 10 Fit the base 1 Attach the base 2 to the ends 1 using 6 screws F and tighten them using the allen key .E .
Assembly Instructions a: Step 12 The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y Fit the back a: Square up the unit by making sure that measurement x to x equals y to y. b: Place the back x b: y D 5 5 onto the unit. Nail D around the outside edges of the back 5 . Note: Nails should be spaced about 150mm apart. y x Stand the unit up for the next step. Warning: The unit is heavy. Lift with care.
Assembly Instructions Step 14 IMPORTANT The unit MUST be fixed to a wall using the bracket supplied. The unit must be level and square before fitting the bracket. Fit the bracket To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket L fitted to the top of the unit. I L Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.
Assembly Instructions Step 15 Fit the door and, if required, the shelf pack and internal chest Please refer to the instructions packed with the door, shelf pack or chest. Door Chest Shelf Door Shelf Shelf If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800 and quote the reference numbers on the component pages.