DR899053 New Hallingford 2 Door 3 Drawer Wardrobe Assembly Instructions - Please keep for future reference 2274951 2498696 2684321 2599409 2328450 Tip: To prevent damage, we recommend that you build your unit on the carton(s) it was packed in.
Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible. • Keep children and animals away from the work area, small parts could choke if swallowed.
Components - Panels If you have damaged or missing parts, call the Customer Helpline: 03456 400 800 Please check you have all the panels listed below 1 Left side (205.6 x 58cm) P2349b 5 Top/Bottom x 2 (96.7 x 57.7cm) P1341 9 Drawer base x 3 (45.4 x 34.9cm) BO33955B 2 Right side (205.6 x 58cm) P2349b 6 Upright small (47.5 x 57.7cm) P2893 10 Drawer wrap x 3 (35 x 46.7 x 10cm) LA1869 3 Mirror door small 4 Door x 1 7 Large horizontal 8 Small horizontal (151.2 x 48.8cm) PS3324 (96.7 x 57.
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. FK1324 A FK1980 B 40mm Screw x 6 C 9mm Srew x 6 20mm Screw x 10 D F E 10mm Fixing screw drawer x 12 FK1235 H L-Bracket x 1 24mm locking screw x 28 FK1012 I Large locking nut x 22 FA1515 FK1010 FK1419 L K Small locking nut x 6 12.
Assembly Instructions Step 1 J Drawer assembly x 3 a: Insert two small locking nuts J into drawer wrap 0. a: Make sure the ‘arrow’ on J�is pointing towards the hole in the edge of 0. 10 J b b: Screw 24mm locking H screws H into holes shown on back of drawer front !. Make sure 24mm locking screws H are tightened right up against drawer front !. H 11 H 11 c: Slide drawer base 9 into grooves shown on drawer wrap 0.
Assembly Instructions Step 1 - continued d: Turn the drawer wrap assembly over and push onto the drawer front !. Use a phillips or flatblade screwdriver, that is a good fit to turn 24mm locking srew I as far as it will go - more than 1/2 turn. d H I 11 I e: Fix drawer handle T onto drawer front ! using 30mm screw B. Turn over drawer and slide drawerbasesupports U in corner as shown and fix them, using the attached screws.
Assembly Instructions Step 2 - continued b: Slide top of runners R b 3 back. E O O R Fix through 3rd hole of runner R and pre-drilled holes of right side 2 using 10mm fixing screw drawer E. Fix through 1st and 7th hole of runners R using 15mm screw O. 3 R O R Note: there are no predrilled holes for 15mm screw O. O R O Repeat a and b on upright small 6. E E E O O O Finished front edge H Step 3 H H Insert fittings Note: Insert 24mm locking screw H as far as shown.
Assembly Instructions Step 4 Attaching plinths a: Allign the sides of A plinth front # with bottom 5 as shown and attach using 40mm screw A. Note: there are no predrilled holes for 40mm screw A. Note: top and bottom panels 5 are identical. Only prepare one of the panels at this satge. This will be the bottom panel A Unfinished back edge A 5 Top side A 14 13 Repeat with plinth back $. H Step 5 5 Insert locking screws H Top side a: Screw 24mm locking screw H into bottom 5.
Assembly Instructions Step 7 H Insert locking screws H Screw 24mm locking screw H into upright small 6. H 6 Unfinished back edge Step 8 Attaching panels 8 Two people are needed here. I Position upright small 6 onto bottom 5 and small horizontal 8. I 6 I M I 5 Insert two Large locking nuts I into upright small 6 and small horizontal 8 where shown. I I Use a screwdriver to turn locking nuts I clockwise to lock.
Assembly Instructions Step 10 M I M I Attaching panel 5 Two people are needed here. I Position left side 1 onto bottom/top 5 and large horizontal 7. Insert large locking nuts I in top/bottom 5 and large horiziontal 7. Use a screwdriver to turn locking nuts I clockwise to lock. I 7 I I I 5 I 1 I Step 11 Fitting back panel Attach foldy back @ to back of wardrobe with the coloured surface facing the inside of the unit using nails K and.
AssemblyInstructions Step 12 Attaching pelment and L-bracket Position pelment % onto top % as shown, fix by using 40mm screws A. A D V G V 5 A 15 Position L-Bracket G onto top 5 as shown, fix by using 15mm screw D. Note: there are no pre-drilled holes for 15mm screw D. Use V to fix on the wall, please see last page for more information. Step 13 N Inserting hanger rails Place hanger rail large N into hanger rail supports M. S M a: b: Step 14 Inserting drawers a: Pull runners out.
Assembly Instructions Step 16 Hanging doors a: With help, slot hinge a: P Q door Q onto hinge back P. P Q P Q P Q b: Tighten screw shown to lock hinges in position. Repeat a and b for other door. See ‘Hinge adjustment’ in step 17 if the doors need adjusting. b: Q Q c: Before adjusting the doors, use a spirit level to check if the base of this unit is level front-to-back and side-to-side in the three positions shown. Use pegs S to square your unit.
AssemblyInstructions Step 17 Hinge adjustment a: To move doors up or down: loosen screws shown and move doors to suit. a: Once doors are aligned, re-tighten. b: To move doors in or out: loosen screw shown and move doors to suit. b: Re-tighten screws. c: To move doors left or right: loosen screw shown and move doors to suit. c: Re-tighten screws.
A Guide to - Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.