Venice - Large Corner TV Unit Assembly Instructions - Please keep for future reference 450/9071 459/9641 Dimensions Width - 119.8cm Depth - 39.19cm Height - 51.2cm MADE IN BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 25kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 1, 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below When applicable, remove any protective film before use 2 Top (DF5746) 1 Side (DF5748) (47.7 x 23mm) (119.8 x 39.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 Prepare the 2 drawer fronts Note: The right drawer front has a small identification hole. A A A Screw 2 metal dowels A into each of the drawer fronts 8 and 9 . A A Note: Tighten the metal dowels up fully against the panels. 8 9 Step 2 Prepare the drawer sides B Insert a small locking nut B into the hole shown on the left drawer side 10 and the right drawer side 11 . B B 10 x2 Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Assembly Instructions Step 4 Fit the drawer base 13 Slide the drawer base 13 down the grooves in the drawer sides 10 and 11 and down into the groove in the drawer front 8 and 9 . 10 11 8 x2 9 Step 5 Fit the drawer back F F Fit the drawer back 12 between the drawer sides 10 and 11 . Make sure that the drawer base 13 fits into the groove in the drawer back 12 . 12 11 x2 13 F 10 F Hold the drawer back 12 in position and tap the knock-in pegs F through the holes in the drawer sides 10 and 11 .
Assembly Instructions Step 8 E E E Prepare the top A Screw 4 metal dowels A into the top 2 . A A A Screw 4 small metal dowels E into the holes on the top 2 . E E 2 Note: Tighten metal dowels up fully against the panels. Step 9 Prepare the top divider Insert 2 large locking nuts C into the top divider 4 . Note: The arrow on the locking nut must point towards the hole in the edge of the panel. Tap 2 wooden dowels H into the top divider 4 .
Assembly Instructions Step 11 C x2 Prepare the 2 horizontals Insert 4 large locking nuts C into each of the 2 horizontals 3 . C C C 3 K K Step 12 Fit a horizontal Attach a horizontal 3 to the top divider 4 using 2 screws K . 3 4 Step 13 G G Fit the 2 large wooden dowels Gently tap the 2 large wooden dowels G through the horizontal 3 and into the top divider . 4 until they ‘’bottom out’’. 7 3 4 Note: Support the horizontal until the right side has been fitted.
Assembly Instructions Step 14 Prepare the right side a: Place a runner P onto one of the sides 1 . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw M . M P 1 a: M P b: Slide the runner P back the other way and fit the 2nd screw M into the corresponding hole in the side 1 . M c: Screw 5 metal dowels B into the side .1 . 1 b: Push 2 hollow core locking nuts D into the side 1 , making sure that they are flush against the panel’s surface.
Assembly Instructions Step 15 1 Fit the right side Push the right side 1 onto the top 2 and the horizontal 3 . 1 The 2 small metal dowels .E fitted to the top 2 must slide into the top of the 2 hollow core locking nuts D fitted to the right side . 1 . Insert a screwdriver into the 2 hollow core locking nuts D and turn the nuts inside as far as they will go. Use a screwdriver to tighten the 2 large locking nuts C fitted to the horizontal 3 .
Assembly Instructions Prepare the lower divider a: Place a runner P onto the lower divider 5 . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw M . P Finished front edge M a: P 5 Finished front edge b: Slide the runner P back the other way and use the 2nd hole from the back to fit the 2nd screw M . M b: 5 Finished front edge c: Tap 2 wooden dowels H into the lower divider 5 .
Assembly Instructions Step 17 Fit the lower divider Finished front edge Push the lower divider 5 down onto the horizontal .3 . 5 3 Step 18 Fit the other horizontal Fit the horizontal 3 to the right side 1 and the lower divider 5 . Attach the horizontal 3 to the lower divider 5 using 2 screws K . Use a screwdriver to tighten the 2 large locking nuts C fitted to the horizontal 3 .
Assembly Instructions Step 19 C Prepare the plinth H Insert 2 large locking nuts C into the plinth 7 . Tap 2 wooden dowels H into the plinth 7 . C 7 H 1 Step 20 Fit the plinth Push the plinth 7 onto the right side 1 . 7 Use a screwdriver to tighten the large locking nut C fitted to the plinth .7 .
Assembly Instructions Step 21 M Prepare the left side P a: Place a runner P onto one of the sides 1 . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw M . M a: 1 P b: Slide the runner P back the other way and fit the 2nd screw M into the corresponding hole in the side 1 . c: Screw 5 metal dowels A into the side .1 . M b: 1 Push 2 hollow core locking nuts D into the side 1 , making sure that they are flush against the panel’s surface.
Assembly Instructions Step 22 Fit the left side Push the left side 1 onto the assembly. Use a screwdriver to turn the nuts inside the 2 hollow core locking nuts .D fitted to the left side .1 . 7 3 1 3 Use a screwdriver to tighten the 5 large locking nuts C fitted to the horizontals 3 and the plinth 7 . 2 Step 23 C Prepare the back C 6 Insert 2 large locking nuts C into each of the back 6 . Step 24 Fit the back Push the back 6 down onto the top 2 .
Assembly Instructions Step 25 Secure the back Secure the back 6 to the 2 horizontals 3 using 4 screws J . Carefully stand the unit up for the next step. 6 3 3 J J Warning: The unit is heavy. Lift with care. J J Step 26 Fit the drawers Slide both the runners P forward and locate the drawer sides 10 and 11 between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners P .