kent 3 door 3 drawer wardrobe Assembly Instructions - Please keep for future reference 552/9713 Dimensions Width - 128 cm Depth - 55 cm Height - 185 cm Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: Argos = 0345 6400800 issue 1 - 9/3/16
! Safety and Care Advice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on the following pages. During assembly do not stand or put weight on the product, this could cause damage. Remove all fittings from the plastic bags and separate them into their groups. Assemble the item as close to its final position (in the same room) as possible. Keep children and animals away from the work area, small parts could choke if swallowed.
Components - Panels If you have damaged or missing components, call the Customer Helpline: Argos = 0345 6400800 Please check you have all the panels listed below 5 Top panel(128 x 5,5 x 3,3 cm) 2 Side panel (53,2 x 4,5 x 146,4 cm) 4 Back panel(121,4 x 1,5 x 146,4 cm) 8 Shelf (43 x 49,7 x 2 cm) 3 Middle panel (49,7 x 4,5 x 146,4 cm) 2 Side panel (53,2 x 4,5 x 146,4 cm) 1 Front panel (83,9 x 2 x 146,4 cm) Short clothes rod (76,9 x 3 x 3 cm) 7 9 The base (128 x 55 x 35,3 cm) 6 Long clothes rod (76,9 x 3
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. A C B D E C Bolts 30mm x 31 Allen Key x 1 F Bracket x 6 G Handle x 3 Shelf Pin x 8 15 mm Screw x 24 I H J Screw & Washer x 3 Ø3.
Assembly Instructions Step 1 Attach the Side panel 2 , Middle panel 3 to the Front panel 1 using 30mm bolts A and secure using the Allen Key B as detail in the diagram below. 1 2 3 2 B A Step 2 Attach the Back panel 4 to the Side panel 2 , middle panel 3 using usnig 30mm bolts A and secure using the Allen Key B as detail in the diagram below.
Assembly Instructions B Step 3 Place the Top panel 5 using 30mm bolts A and secure using allen key B Then using screw D secure bracket C . A 5 C D E Step 4 8 Attach handle to the door F using srcews and washer G .Slide Long clothes rod 6 , short clothes rod 7 into the hanger.Then insert shelf pin E into the desired position and put the shelf 8 .
Assembly Instructions Step 5 Drawer handles are pre-assembled reversely. Disassemble the handle and re-attach as shown in the figure.
Assembly Instructions Step 6 Put the assembled frame onto The Base 9 .Then using 30mm bolt A and secure using allen key B as detail in the diagram below. B A 9 Step 7 Using screw 15mm D and bracket C to hold frame with the base 9 .
Assembly Instructions Step 8 Fixing strap to wall. Note: The correct type of wall screws must be used for your wall. Please seek professional advice if in doubt. I It is recommended that the unit is fixed to a wall. ! Mark fixing hole on wall. Fasten wall strap I to the wall using a suitable wall screw/plug system. ! 183 cm ! Warning: Before drilling, check wall for hidden pipes and cables. Step 9 J Fixing unit to wall. H With the help of another person move the unit into position.
A Guide to - Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualifed tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
