Suki TV Unit Assembly Instructions - Please keep for future reference 609/7426 Dimensions Width - 92cm Depth - 37cm Height - 43cm Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800 Version 2 Date:26/03/13
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Check you have all the components and tools listed on pages 2 and 3. • Remove all fittings from the plastic bags and separate them into their groups. • Keep children and animals away from the work area, small parts could choke if swallowed. • Make sure you have enough space to layout the parts before starting. • Do not stand on the product, this could cause damage.
Components - Panels If you have damaged or missing components, call the Customer Helpline: 08456 400800 Please check you have all the panels listed below Finished front surface Finished front edge 1 2 7 Right shelf 9 Middle shelf x 2 (49.6 x 36.6cm) (17.7 x 14.5cm) 8 Left shelf (17.7 x 14.5cm) Top panel (91.6 x 36.8cm) Bottom panel (91.6 x 36.8cm) Finished front edge 10 Back panel x 2 (19.2 x 38.6cm) 3 Middle right panel (36.7 x 38.6cm) 4 Middle left panel 6 Left side panel (36.
Components - Fittings Note: The quantities below are the correct amount to complete the assembly. in some cases mor may be supplied than are required.
Assembly Instructions Step 1 Fitting dowels a: a: Insert Dowels A into the Middle right panel 3 and Middle left panel 4 . 3 A A 4 A A b: Insert Dowels A into the Right shelf 7 and Left shelf 8 .
Assembly Instructions Step 2 Attaching left and right shelves a: back edge a: Use Screws B to Middle left panel 4 onto the Left shelf 8 . 4 B back edge 8 back surface b: Use Screws B to b: Middle right panel 3 onto the Right shelf 7 .
Assembly Instructions Step 3 Attaching middle shelves a: Middle shelves the unit. B 9 onto a: Unfinished back edge Unfinished back surface 9 9 4 B B B B b B Middle right panel 3 onto the unit.
Assembly Instructions Step 4 Attaching side panels a: a: Position Left side panel 6 onto the unit. back edge 8 6 b: Position Right side panel 5 onto the unit.
Assembly Instructions Step 5 Attaching bottom panel B C C B onto the unit. back surface 5 3 4 C 2 B B 6 C C B B C B B B Step 6 Inserting back panels a: Place a small amount of Glue G into the grooves of Middle right panel 3 and Middle left panel 4 . a: G G 3 G 4 Continued on next page.
Assembly Instructions Step 6 - continued b: Carefully slide Back panels 10 into the grooves. b: back surface 10 back surface 3 10 4 6 Step 7 a: Attaching top panel a: Screw Locking pins into the Top panel 1 D D . Note: Insert locking pins as far as shown. Do not over tighten. D D D D 1 D D Continued on next page.
Assembly Instructions Step 7 - continued b: Position Top panel onto the unit. Insert 6 Locking nuts into the unit. 1 b: F F Use a screwdriver to turn Locking nuts F clockwise to lock. 1 5 F 3 F F 4 6 Step 8 E Fixing back panels Attach Back panels 10 onto the unit using Nails E . Important: The unit MUST be ‘square’ when back is attached.
Assembly Instructions Step 9 Finishing the unit Note: It would be useful to ask someone to help you at the stage. With help, place the unit in the intended position. Note: Before use allow the glue to dry for 24 hours and make sure the unit is secure. Assembly is complete.
