Square + 4 x 2 Assembly Instructions - Please keep for future reference 620/2493 616/6182 hygena 617/4260 622/9919 WARNING! In order to prevent overturning, this product must be used with the 2 wall attachment devices provided Dimensions Width - 75.9cm Depth - 39.1cm Height - 145.5cm MADE IN BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 35kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below When applicable, remove any protective film from the panels before they are used 1 Top/Base (DF8709) (75.9 x 39.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 C Prepare the 2 end panels C x2 Insert 4 minifix nuts C into both of the end panels 2 . C 2 Note: The arrow on the minifix nuts must point towards the hole in the edge of the panel. C Step 2 Prepare the 3 shelves C A A A x3 A Gently tap 8 long wooden dowels A into each shelf 3 until they ‘’bottom out’’. 3 A A A A Step 3 Fit 2 shelves to an end panel Push 2 of the shelves 3 down onto an end panel .2 . 3 3 Now carefully lay the unit onto its side.
Assembly Instructions Step 4 A A Fit a divider A A Position a divider 4 between the 2 shelves 3 . 4 Gently tap 4 long wooden dowels A through the holes in each shelf 3 and into the divider 4 until they ‘’bottom out’’. A A 3 3 A A Step 5 Fit another divider Carefully turn the unit back onto its end panel. Warning: The unit is heavy. Lift with care. Push a divider 4 onto the shelf 3 . 3 4 Note: Support this divider until the final shelf has been fitted in the next step.
Assembly Instructions Step 7 Fit the remaining end panel Push the remaining end panel 2 down onto the 3 shelves 3 . 2 3 3 3 Step 8 Fit a divider Carefully stand the unit upright. Warning: The unit is heavy. Lift with care. A A A A Push a divider 4 down onto the shelf 3 . Gently tap 4 long wooden dowels A into the divider 4 until they ‘’bottom out’’.
Assembly Instructions D Step 9 D Prepare the base panel D Stick a felt pad D into each corner of the base panel 1 . 1 D B Turn the base over Turn the base over B Screw 4 metal dowels B into the base panel 1 . B Note: Tighten the metal dowels up fully against the panels. B B 1 Step 10 B Fit the base panel Push the base 1 down onto the assembly. Use a screwdriver to tighten the 2 minifix nuts .C fitted to each of the end panels 2 .
Assembly Instructions Step 11 Warning: The unit is heavy. Lift with care. Fit the final divider A A A A Carefully turn the unit over. Push a divider 4 down onto the shelf 3 . Gently tap 4 long wooden dowels A into the divider 4 until they ‘’bottom out’’. 4 3 Step 12 Prepare the top panel B B Screw 4 metal dowels B into the top panel 1 .
Assembly Instructions Step 13 Fit the top panel Push the top 1 down onto the assembly. Use a screwdriver to tighten the 2 minifix nuts .C fitted to each of the end panels 2 .
Assembly Instructions Step 14 Fit the 2 overbalance protector kits Important: A bracket must be fitted on both sides of the unit and they must be at least 25mm in from the end panels. To prevent possible overbalancing this unit must be secured to a suitable wall by fitting of the 2 overbalance protector kits E to the unit, or an alternative fixing method of your choice.
Assembly Instructions Step 15 If required, fit your door or drawer inserts If you have purchased door or drawer inserts, please refer to the assembly instructions packed with them. Drawer Insert Door Insert If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.