Eros 4'6, 5'and 6' Ottoman Beds Assembly Instructions – Please keep for future reference 750/7269 742/9031 745/1731 hygena Dimensions (4'6') Dimensions (5') Dimensions (6') Length - 203cm Length - 214cm Length - 214cm Width - 144.5cm Width - 159.5cm Width - 189.
Safety and Care Advice Check you have all the components and tools listed on pages 2 and 3. Assemble the item as close to its final position (in the same room) as possible. Remove all fittings from the plastic bags and separate them into their groups. Assemble on a soft level surface to avoid damaging the unit or your floor. Keep children and animals away from the work area, small parts could choke if swallowed. Assembly requires 2 people.
0345 6400 800 INSIDE Right side rail (4.6'-1930 × 310mm)(5'/6'-2030 × 310mm) INSIDE FRONT Left side rail (4.6'-1930 × 310mm)(5'/6'-2030 × 310mm) Headboard (4.6'-1445 × 920mm) (5'-1600 × 920mm) (6'-1890 × 920mm) INSIDE Footboard (4.6'-1445 × 310mm) (5'-1600 × 310mm)(6'-1890 × 310mm) Hinges x 2 (750 x 115mm) Piston x 2 (420mm) Base panel x2 (4/6-1377 × 600mm) (5'-1527 × 600mm) (6'-1827 × 600mm) Base panel x1 (4/6-1377 × 724mm) (5'-1527 × 824mm) (6'-1827 × 824mm) Feet x 4 (62 x 33 x 41.
Components --Parts Parts Components If you have damaged or missing components, call the Customer Helpline: 0345 6400 800 Please check you have all the parts listed below 13 Ottoman frame (Sides) x 2 (4'6-1822*30mm)(5'/6'-1925*30mm) 14 Ottoman frame centre rail x 1 (4'6-1822*30mm)(5'/6'-1925*30mm) 16 Central support x 1 (4'6-1930*80mm) (5'/6'-2030*80mm) 18 Wooden support rail x 2 (4'6-1379*60mm) (5'-1529*60mm) (6'-1829*60mm) 21 Single slat caps x 28 (4'6-5.5mm) Single slat caps x 30 (5'/6'-5.
Components - Fittings If you have damaged or missing components, call the Customer Helpline: 0345 6400 800 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 Attaching feet D a: Attach 2 x Feet 9 to the underside of the headboard 3 using screws D as shown. Repeat on the underside of the footboard 4 . Note: The position is outlined.
Assembly Instructions Step 2 Preparing footboard Attach the ottoman frame support 23 to the footboard 4 using fixings A and F as shown. 4 23 F A Step 3 Preparing footboard and headboard With help, carefully place headboard 3 and footboard 4 flat onto the floor with the fixing holes facing up as shown. D Note: Ensure the floor is suitably clean and protected to prevent any damage to the headboard and footboard. Attach base supports 17 to the footboard 4 and headboard 3 as shown using screws D .
Assembly Instructions Step 4 Attaching side rails a: B a: Loosely fit bolts B into headboard 3 and footboard 4 as shown. 3 B 4 b: With help, raise headboard 3 into the standing position. b: Hang the metal brackets on the end of the side rails 1 and 2 , over the bolts in the headboard 3 . 3 2 B Note: Ensure the 4 holes on the inside of each side rail are located at the headboard end as shown. 3 Note: Do not fully 2 tighten bolts B at this stage. Finger tighten only.
Assembly Instructions Step 5 Preparing base c: C a: Attach the short support legs 19 to the underside of the central support 16 using bolts C . 1 18 3 Fit plastic caps G into support legs 19 . 1 18 16 b: Assemble central 18 support 16 in between headboard 3 and footboard 4 using fixings C and H at both ends. 2 b: 3 4 H C c: Assemble wooden support rails 18 in between side rails 1 and 2 using screws C . Finally, fully tighten all other fixing points from previous step 4 .
Assembly Instructions Step 6 Completing base With help, carefully slide base panels 7 and 8 inside the bed frame as shown. 7 8 7 Step 7 Attaching folding hinges a: Secure hinges 5 to side rails 1 & 2 using bolts C as shown. up b: 5 Note: Ensure the hinges E are fitted the correct way around as shown. 6 b: Locate pistons 6 onto up hinges 5 as shown. Note: Ensure the "smaller" 5 a: tube is facing down as shown. down C Secure the pistons using nuts E at both ends.
Assembly Instructions Step 8 Assembling ottoman frame C 10 a: a: Assemble long support legs 10 to the underside of centre rail 14 and end frame 11 using screws C . b: Assemble ottoman frame components 11 , 12 , 13 and 14 together as shown. 11 C 10 14 B b: Headboard end F 11 13 Note: Secure the assembly using fixings B and F as shown. 14 13 Upside down 12 Important Do not fully tighten screws B at this stage. Finger tighten only. c: With help, carefully turn the frame over.
Assembly Instructions Step 9 Locating ottoman frame With help, lift the ottoman frame into position onto the top of hinges 5 . 13 5 Note: The frame is heavy, lift with care. C Secure on both sides using screws C . Once assembly is complete, fully tighten all screws around the ottoman frame.
Assembly Instructions Step 10 Attaching single slat caps 21 15 Assemble single slat caps 21 onto one end of bentwood slats 15 . Step 11 a: Attaching slats 21 15 a: Fit bentwood slats 15 into the ottoman frame (sides) 13 by locating single slat caps 21 into the holes. 21 15 20 b: Fit bentwood slats 15 into both sides of double slat caps 20 , before pushing caps 20 into the holes in central support 14 . 15 13 21 15 14 20 13 b: 14 Assembly is complete.