Wide Media Unit Assembly Instructions - Please keep for future reference 457/2156 625/9563 651/5070 Dimensions Width - 60.5 cm Depth - 19.
Safety and Care Advice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on the following pages. During assembly do not stand or put weight on the product, this could cause damage. Remove all fittings from the plastic bags and separate them into their groups. Assemble the item as close to its final position (in the same room) as possible. Keep children and animals away from the work area, small parts could choke if swallowed.
Components - Panels If you have damaged or missing components, call the Customer Helpline Argos = 0345 6400800 Please check you have all the panels listed below Unfinished edge Unfinished edge 1 Top panel x 1 (60.5 x 13.1cm) 2 Bottom panel x 1 (60.5 x 19.6cm) Unfinished edge 3 Left Side panel x 1 (111 x 13cm) Unfinished edge 4 Right Side panel x 1 (111 x 13cm) 8 Middle Shelf x 3 (15 x 12.8cm) 5 Shelf panel(use screw) x 1 (58 x 12.9cm) 6 Shelf panel(use dowel) x 4 (58 x 12.
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. B A 38mm Screw x 12 C Nail x 38 30mm dowel x 56 D F E Stickers x 8 26mm Screw x 2 12mm Screw x 2 G H J Wall plug x 2 Wall strap x 2 Tools required Phillips screwdriver (medium & large) Ruler/tape measure hammer.
Assembly Instructions Step 1 a: Insert dowels a: Insert dowel B B G middle panels 8 into 9 . B B B 8 X3 9 X6 B B B B b: Insert dowel B into shelf panel 6 and side panel 3 4 .
Assembly Instructions Step 2 a: Attaching panels a: Attaching panel 5 6 8 9 using dowel as shown. Attention to the position of shelf 5 .
Assembly Instructions Step 2 b: Attaching panels b: Attaching the side panels 3 4 with screw A . A A 3 A 4 A c: Attaching the top 1 panel onto unit with screw A .
Assembly Instructions Step 2 d: Attaching panel d: Attaching the bottom panel 2 onto unit with screw A . A 2 A A A Step 3 Attaching back panels a: Turn the unit up side down. Lift with care.
Assembly Instructions Step 3 Attaching back panels b: b: Attaching the back panel 7 . One piece first, using nail C . Don’t put the nail too close to the corner to avoid the screw penetrate the panel. 7 suggest to add a nail in the middle of the back panel to reinforce the structure C c: Fix the another back panel 7 onto the unit using nail C .
Assembly Instructions Step 3 Attaching back panels d: d: Fit the wall strap H onto the back of unit with screw F . H H F F Step 4 Paste sticker Paste sticker D onto the screws on top panel and side panels.
Assembly Instructions Step 6 G Fixing to wall It is recommended that the storage unit is fixed to a wall. E fi H With help, move storage unit into position. Lift with care. Mark fixing hole on wall and remove storage unit. Drill 7mm hole and insert wall plug G . Before drilling, check wall for hidden pipes and cables. Reposition storage unit and fix wall strap using screw E .
A Guide to - Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualifed tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
