Pagnell Bookshelf Assembly Instructions - Please keep for future reference 709/2664 Dimensions Width - 73cm Depth - 40.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Check you have all the components and tools listed on pages 2 and 3. rom the plastic bags and separate them into their groups. • Keep children and animals away from the work area, small parts could choke if swallowed. • Make sure you have enough space to layout the parts before starting. • Do not use this item if any components are missing or damaged. • Do not stand on the product, this could cause damage.
Components - Panels If you have damaged or missing components, call the Customer Helpline: 08456 400800 Please check you have all the panels listed below 1 Top panel (73 x 40cm) 5 Shelf x 2 (69.8 x 37.9cm) 6 Front panel (69.8 x 4.5cm) Finished front edge 2 Right side panel (38 x 98.4cm) 3 Left side panel (38 x 98.4cm) 7 Back panel (72.4 x 95.2cm) 4 Bottom panel (69.8 x 37.
Components - Fittings Note: The quantities below are the correct amount to complete the assembly. in some cases mor may be supplied than are required.
Assembly Instructions Step 1 a: Fitting dowels A a: Insert Dowels A into the Bottom panel Shelves 5 . 4 4 and A A A 5 x2 A b: Insert Dowels A into the Right side panel 2 and Left side panel 3 . b: A A 2 A 3 Step 2 a: Attaching plastic supports a: C Plastic supports B the Front panel 6 C C B onto . C 6 B B C B Continued on next page.
Assembly Instructions Step 2 b: continued C b: C C C Front panel 6 onto the Bottom panel 4 . 6 C 4 Step 3 D D D Fitting locking pins D Screw Locking pins D into the Right side panel 2 and Left side panel 3 . D 2 D D D Note: Insert Locking pins as far as shown. Do not over tighten. D D D D 3 D Step 4 a: E Attaching bottom panel Position Bottom panel 4 onto the Left side panel 3 . Insert Locking nuts E into the Bottom panel back edge 4 .
Assembly Instructions Step 5 Attaching shelves Position Shelves the unit. 4 5 back edge onto 5 E 5 Insert Locking nuts E into the Shelves 54 . E E Use a screwdriver to turn Locking nuts E clockwise to lock. 3 E Step 6 Attaching right side panel back edge 2 Position Right side panel 2 onto the unit. E Insert Locking nuts E into the Shelves 5 and Bottom panel 4 . 5 E 5 E Use a screwdriver to turn Locking nuts E clockwise to lock.
Assembly Instructions Step 7 - continued b: Position Top panel 1 b: E onto the unit. Insert Locking nuts E into the Right side panel 2 and Left side panel 4 . back edge Use a screwdriver to turn Locking nuts E clockwise to lock. 1 E E 2 E E 3 Step 8 Fixing back panel Attach Back panel 7 onto the unit using Nails F . Important: The unit MUST be ‘square’ when back is attached.
Assembly Instructions Step 9 Fixing to wall It is recommended that Fix Wall strap H to back of top panel using Screw C . With help, move bookshelf into position. wall G H wall. Note: Wall plugs supplied are for solid wall only. be used for your wall, seek professional advice if in doubt H C H H G Top panel Warning: The bookshelf is heavy. Lift with care. and remove bookshelf. Back panel Drill a hole and insert Wall plug G . Warning: Before drilling, check wall for hidden pipes and cables.
A Guide to - Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.