Malibu - 5+2 Drawer Chest Assembly Instructions - Please keep for future reference 558/8228 539/6173 544/1341 541/5566 CR 542/1907 CR CR CR CR CR CR WARNING! In order to prevent overturning, this product must be used with the wall attachment device provided Dimensions Width - 74.8cm Depth - 39cm Height - 108.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 38kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below When applicable, remove any protective film before use 3 Top (DF6780) (74.8 x 39.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 Prepare 5 pairs of drawer sides a: Insert a large locking cam nut B into the left drawer sides 11 and the right drawer sides 12 . Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 14 Standard Drawer Box Assembly https://www.youtube.com/watch?v=HclfJdkm-Lg a: B Note: Only the plastic thread of the quickfit dowel sticks out from the panel. 12 11 Note: The arrow on the locking cam nut must point towards the hole in the end of the panel.
Assembly Instructions Step 3 Standard Drawer Box Assembly https://www.youtube.com/watch?v=HclfJdkm-Lg Fit the large drawer bases Slide a large drawer base .16 down the grooves in the drawer sides 11 and .12 and down into the groove in the large drawer front 10 . 16 11 x5 10 Step 4 Fit the large drawer backs C x5 Fit a large drawer back 14 between the drawer sides 11 and 12 . Make sure that the large drawer base 16 fits into the groove in the large drawer back 14 .
Assembly Instructions Step 7 Prepare 2 pairs of drawer sides a: B B B a: Insert a large locking cam nut B into the left drawer sides 11 and the right drawer sides 12 . Note: The arrow on the locking cam nut must point towards the hole in the end of the panel. 12 11 x2 x2 b: b: Push 1 of the quickfit dowels A as far as it will go into the left drawer side 11 and the right drawer side 12 . 12 11 A x2 A x2 A Note: Only the plastic thread of the quickfit dowel sticks out from the panel.
Assembly Instructions Step 9 Fit the small drawer bases 15 x2 12 Slide a small drawer base 15 down the grooves in the drawer sides 11 and 12 and down into the groove in the small drawer front 8 and 9 . 11 8 9 Step 10 Fit the small drawer backs x2 Fit a small drawer back 13 between the drawer sides 11 and 12 . Make sure that the small drawer base 15 fits into the groove in the small drawer back 13 .
Assembly Instructions Fit the DR runner N d to the bottom edge of the right drawer side 12 using the same method. x5 F F F 12 F 11 DL Fit the DL runner N c to the bottom edge of the left drawer side 11 , as shown, making sure that it is pushed up against the back of the drawer front. Use a bradawl to mark the fixing positions, then secure with 2 screws F . Runners must be pushed up against the drawer front DL Fit runners to the 5 large drawers Fixing Bottom Mounted Runners https://www.youtube.
Assembly Instructions Step 15 Use the Main Fittings Bag for Steps 15 - end Fixing Bottom Mounted Runners https://www.youtube.com/watch?v=Z6lGMy19h7Q Prepare the left side a: Fit 6 CL runners N a to the left side 1 . Finished front edge The 1st screw I uses the 1st hole in from the front of the runner. 1st screw I N a CL The 2nd and 3rd screws . I use the holes that line up with the other panel holes.
Assembly Instructions Step 16 N b a: Fit 6 CR runners N b to the right side 2 . CR The 1st screw I uses the 1st hole in from the front of the runner. I I I I I N b N b R Finished front edge R C N b N b R C b: Fit a screw F into the hole at the top of the runner N b . N b R I I C I I I R I I C a: I I I R C I I I C The 2nd and 3rd screws . I use the holes that line up with the other panel holes.
Assembly Instructions Step 17 H H Note: The cross rail has no holes drilled on either surface Prepare the cross rail Tap 4 wooden dowels H into the cross rail 6 . 6 Finished front edge H H Step 18 Fit the cross rail onto the left side Push the cross rail 6 down onto the left side .1 . Finished front edge 6 L C Finished front edge L C L C L C 1 L C L C Step 19 Prepare the plinth Insert 2 large locking cam nuts B into the plinth 5 .
Assembly Instructions Step 20 Carcase Assembly https://www.youtube.com/watch?v=9C7tgv5xnbE Fit the plinth Push the plinth 5 down onto the left side 1 . L C Turn the large locking cam nut B clockwise to the “2 o’clock” position as far as it will go to secure the panels. 5 L C L C L C 1 L C L C Important: Make sure there is no gap between the fitted panels. B Step 21 Prepare the 2 back rails Insert 2 large locking cam nuts B into each of the back rails 7 .
Assembly Instructions Step 23 Fit the other back rail Push the back rail 7 down onto the left side .1 . L C Turn the large locking cam nut B clockwise to the “2 o’clock” position as far as it will go to secure the panels. L C L C 7 L C L C 1 L C Important: Make sure there is no gap between the fitted panels. Step 24 Fit the right side Push the right side 2 down onto the assembly.
Assembly Instructions Step 25 Fit a runner N a to the divider 4 . The 1st screw I uses the 1st hole in from the front of the runner. b: Fit a screw F into the 2nd hole in at the top of the runner N a . I N a N a CL 4 Finished front edge F F b: 4 B H A Finished front edge H B c: A L C c: Insert 2 large locking cam nuts B into the divider 4 . I Finished front edge The 2nd and 3rd screws . I use the holes that line up with the other panel holes.
Assembly Instructions Step 26 Fit the divider to the top Push the divider 4 down onto the top 3 . 3 4 Finished front edge Turn the 2 large locking cam nuts B clockwise to the “2 o’clock” position as far as they will go to secure the panels. Important: Make sure there is no gap between the fitted panels. Step 27 Fit the top Push the top 3 down onto the assembly. Turn the 4 large locking cam nuts B clockwise to the “2 o’clock” position as far as they will go to secure the panels.
Assembly Instructions Step 28 Squaring up a Chest and fitting the Back Panel www.youtube.com/watch?v=FeaI6541z7o Fit the back a: Square up the unit by a: b: Place the back 17 onto the unit. b: making sure that measurement x to x equals y to y. The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y x K Nail K around the outside edges of the back 17 . Note: Nails should be spaced out evenly.
Assembly Instructions Step 30 Fit the overbalance protector kit a: Before fitting the overbalance protector kit, use a spirit level to check the top of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level.
Assembly Instructions Step 31 Fixing Bottom Mounted Runners https://www.youtube.com/watch?v=Z6lGMy19h7Q Fit the drawers Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position. Assembly is complete CR CR CR CR CR CR CR Side panel Drawer If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.
ALR3296
