Bunk bed - Grey 190x90 cm Assembly Instructions - Please keep for future reference 7985290 Dimensions Length - 195cm Depth - 96/102cm Height - 144,5cm Weight - 43kg Important – Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 0045 7668 8055 or e-mail: order@flexa.
Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on pages 2, 3 and 4. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible. • Keep children and animals away from the work area, small parts could choke if swallowed.
Components - Parts If you have damaged or missing components, call the Customer Helpline: 0045 7668 8055 Please check you have all the parts listed below 1 4 7 8 Slat x30 (89.7x6.5x1.5cm) No. 12-01508971 End panel x4 (87.7x27.6x0.8cm) No. 4301-0808771-65 2 5 List f. safety x2 (31.8x2.8x1.2cm) No. 12-01203181-65 Tread (w/ 3 holes) x1 (35.0x6.5x2.0cm) No. 12-02003504-65 3 6 Tread (w/ 4 holes) x1 (35.0x6.5x2.0cm) No. 12-02003503-65 Endrail x8 (87.7x6.5x2.0cm) No.
Components - Parts Please check you have all the parts listed below 10 Safety rail 3/4 x2 (149.7x6.5x2.0cm) No. 12-02014971-65 11 Safety rail 1/1 x2 (186.7x6.5x2.0cm) No. 12-02018673-65 12 Ladderside bunkbed x1 (114.8x8.9x2.0cm) No.
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. No. 3922-06014 No. 3913-06090 A C B M6x90mm Connecting bolt x8 M6 Ø10x14mm Barrel nut x8 No. 3930-10045 10x45mm Dowel x22 4,5x40mm Chipboard screw x4 No. 3901-40030 E D No. 3901-45040 No. 3909-63050 F 4,0x30mm Chipboard screw x72 6,3x50mm Assembly screw x8 No. 3909-63090 No.
Assembly Instructions Step 1 Insert dowels D to bedsides 7 – and to all the safety rails 10 and 11 . It may be necessary to tap the dowel in very gently with a small hammer. 11 D x2 D Repeat same procedure for all bedsids 7 and all safety rails 10 and 11 .
Assembly Instructions Step 3 Attach leg 9 to endrails 6 with screws J using the allen key. J 6 J 8 Attach leg to endrails 6 with screws J using the allen key. 6 Repeat same procedure for both headboard and footboard 9 6 J Step 4 6 During assembly of headboard and footboard, you must decide if the grooves in the MDF panels, should face in or out of the bed 8 6 4 Slide panel 4 between endrails 6 . Attach legs 8 / 9 to endrails 6 with screws J using the allen key.
Assembly Instructions Step 5 Attach bedside 7 and both safety rails 11 to the bed firstly by placing the dowels in holes in the legs. A Push barrel nuts B into the 2 small holes in bedside 7 push 1 connecting bolt A through each leg 9 to meet barrel nuts B and then fasten with the allen key. B J A J J 8 B B A 9 Push 4 assembly screws J through legs 9 to meet the safety rails 11 and then fasten with the allen key.
Assembly Instructions Step 8 Attach the 2 beds by putting the one bed (with legs 9 ) in top of the other bed. J C 9 Attach the connecting double bolt N in legs 8 with the upper bed by screws C through legs 9 . C 9 10 C 10 Step 9 N 9 Push 2 assembly screws J through the leg 9 to meet the safety rails 10 and then fasten with the allen key.
Assembly Instructions Step 11 Place 1 slat 1 in the center of the bed and two slats 1 in both ends of the bed, 16mm from bed ends. Follow the measurements. Push the bedsides 7 together whilst attaching slat 1 to the bed with 2 chipboard screws E E PUSH E E 8 16 mm 832 mm Position the remaining 12 slats 1 in the bed with a distance of 63 mm between each.
Assembly Instructions Step 12 Attach the safety list 2 inside the bed, on the front safety rails 10 . Should be in the center of the front guards between the slats. E 9 Max mattress height! Attach it 2 to the safety rails 10 and bedside 7 with chipboard screws E E O Follow the measurement. 2 Attach the safety list 2 on the outside of the bed, on the back safety rails 11 . Should be in the center of the back guards.
Assembly Instructions Bunkbed as 2 single beds 9 Note: To acheive the single bed look shown on the picture, one end of the upper bunk (assembled components 4 , 6 and 9 ) should be swapped over with the lower bunk (assembled components 4 , 6 and 8 ). 6 6 9 6 8 6 9 6 8 6 9 6 8 6 8 If you need help or have damaged or missing parts, call the Customer Helpline: 0045 7668 8055 E-mail: order@flexa.dk 11 Ref.no.
