Adult Malibu - 3 Drawer Bedside Chest Assembly Instructions - Please keep for future reference 548/5840 542/6122 555/0847 539/6489 541/0688 381/0840 368/3871 CR 381/2752 380/5903 CR 381/6521 CR More help is available throughout this booklet by scanning in the QR codes or typing in the links Dimensions Width - 38.3cm Depth - 39.6cm Height - 60.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 15kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 7 Prepare the drawer sides a: Insert a large locking cam nut B into the left drawer sides 8 and the right drawer sides 9 . Note: The arrow on the locking cam nut must point towards the hole in the end of the panel. b: Push 1 of the quickfit dowels A as far as it will go into the left drawer side 8 and the right drawer side 9 .
Assembly Instructions Step 3 Fit the drawer bases Slide a drawer base 11 down the grooves in the drawer sides 8 and 9 and down into the groove in the drawer front 7 . x3 11 9 8 7 Step 4 Fit the drawer backs x3 Fit a drawer back 10 between the drawer sides 8 and 9 . Make sure that the drawer base 11 fits into the groove in the drawer back 10 . C C 10 9 C 11 C 8 Hold the drawer back 10 in position and tap the knock-in pegs C through the holes in the drawer sides 8 and 9 .
Assembly Instructions Step 6 Fit the wedgefixes E Turn the drawer assemblies over and slide 2 wedgefixes E into the front and back grooves, as shown, and tighten up the screws. Step 7 Fit runners to the drawers Fit the DL runner M c to the bottom edge of the left drawer side 8 , as shown, making sure that it is pushed up against the back of the drawer front 7 . Use a bradawl to mark the fixing positions, then secure with 2 screws F .
Assembly Instructions Step 8 Use the Main Fittings Bag for Steps 8 - end Prepare the left side Fixing Bottom Mounter Runners https://www.youtube.com/watch?v=Z6lGMy19h7Q a: Fit 3 CL runners M a to the left side 1 . H Finished front edge The 1st screw H uses the 1st hole in from the front of the runner. 1st screw M a CL The 2nd and 3rd screws .H use the holes that line up with the other panel holes.
Assembly Instructions Step 9 a: Fit 3 CR runners M b to the right side 2 . M b CR The 1st screw H uses the 1st hole in from the front of the runner. H H H H H H R C H M b R C a: H H M b R C The 2nd and 3rd screws .H use the holes that line up with the other panel holes. Finished front edge 1st H screw Prepare the right side 2 M b Finished front edge b: Fit a screw F into the hole at the top of the runner M b . c: Insert 2 large locking cam nuts B into the right side 2 .
Assembly Instructions Step 10 G G Note: The cross rail has no holes drilled on either surface Prepare the cross rail 6 Tap 4 wooden dowels G into the cross rail 6 . Finished front edge G Step 11 Fit the cross rail onto the left side Finished front edge 6 L C Finished front edge L C Push the cross rail 6 down onto the left side .1 . G 1 L C Step 12 Prepare the plinth Insert 2 large locking cam nuts B into the plinth 4 .
Assembly Instructions Step 14 A B Prepare the back rail Insert 2 large locking cam nuts B into the back rail 5 . B G A B Push 2 of the quickfit dowels A as far as they will go into the back rail .5 . 5 A Tap 2 wooden dowels G into the back rail 5 . G Step 15 Fit the back rail L C Push the back rail 5 down onto the left side .1 . L C 1 5 L C Turn the large locking cam nut B clockwise as far as it will go to secure the panels. Important: Make sure there is no gap between the fitted panels.
Assembly Instructions Step 17 Fit the top 3 Push the top 3 down onto the assembly. Finished front edge CR CR Turn the 4 large locking cam nuts B clockwise as far as they will go to secure the panels. CR Important: Make sure there is no gap between the fitted panels. Squaring up a Chest and fitting the Back Panel www.youtube.com/watch?v=FeaI6541z7o Step 18 Fit the back a: Square up the unit by a: b: Place the back 12 onto the unit. b: making sure that measurement x to x equals y to y.
Assembly Instructions Step 19 Fit the 4 plastic nails 2 CR Carefully stand the unit up for the next step. I CR Tap 2 plastic nails I into the bottom edge of each of the sides 1 and .2 . I 1 I I Step 20 Fit the overbalance protector kit a: Before fitting the overbalance protector kit, use a spirit level to check the top of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level.
Assembly Instructions Step 21 Fit the drawers Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position. Assembly is complete Fixing Bottom Mounter Runners https://www.youtube.com/watch?v=Z6lGMy19h7Q CR CR CR Side panel Drawer If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.
ALR3317
