Heavy Duty - Bunk Bed Assembly Instructions - Please keep for future reference 557/5554 542/4825 814/8809 Dimensions Width - 205,8cm Depth - 102,8cm Height -159,0cm Important – Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800 Issue 1 - 27/04/20
Safety and Care Advice Important – Please read these instructions fully before starting assembly . Check you have all the components and tools listed on pages 2 and 3. . Remove all fittings from the plastic bags and separate them into their groups. . Keep children and animals away from the work area, small parts could choke if swallowed. . Make sure you have enough space to layout the parts before starting. . Assemble on a soft level surface to avoid damaging the unit or your floor. .
Components - Panels Please check you have all the panels listed below 09 Short guard rail x2 (150,0 x 9,0 x 1,9 cm) 10 Front side rail x2 (190,0 x 11,0 x 4,4 cm) 11 Back side rail x2 01 Upper Right Headboard x1 (190,0 x 11,0 x 4,4 cm) (100,8 x 77,0 x 7,0 cm) 12 Slats x 04 (91,0 x 7,0 x 1,7 cm) 13 Slats x 24 (91,0 x 7,0 x 1,7 cm) 14 Short Ladder Side Rail x1 (89,2 x 6,5 x 2,3 cm) 02 Upper Left Headboard x1 (100,8 x 77,0 x 7,0 cm) 15 Long Ladder Side Rail (120,2 x 6,5 x 2,3 cm) 03 Lower Headboard x
Components - Fittings If you have damaged or missing components, call the Customer Helpline: 03456 400 800 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 Inserting wooden dowels A Insert wooden dowels A and wooden dowels B into the indicated parts. A A A B 11 05 x3 10 x2 B 08 x2 A 09 x2 A A x2 A A A Step 2 M Fitting top rails Insert wooden dowels A into Lower headboard 3 as shown. E Fix Lower top rail 7 to Lower headboard 3 using bolt E and allen key M , as shown. M + 03 E M Do not over tighten screws + E M Repet step 2 for the other lower headboard.
Assembly Instructions Step 3 Fitting top rails M Insert wooden dowels A into upper top rail 6 , as shown. Fix upper left headboard 2 to upper top rail 6 using bolt E and allen key M , as shown. E M Do not over tighten screws + 02 E M + E M + E A A 06 A Step 4 M Fitting top rails Insert wooden dowels A into upper right headboard 1 , as shown. E Fix upper right headboard 1 to upper top rail 6 using bolt E and allen key M , as shown.
Assembly Instructions Step 5 I GG++MM Fixing side rails ! G Attention F From this step are, two people are required for an easier assembly. F 11 I With help, fix front side rail 10 and back side rail 11 to Lower headboard 3 using bolt F and G and allen key M , as shown. ! G 03 I Insert half moon nuts I into side rails, as shown. +M +M +M +M 10 Make sure front side rail 10 is posioned as shown in the diagram.
Assembly Instructions Step 7 Fixing side rails Insert half moon nuts I into side rails, as shown. With help, fix front side rail 10 and back side rail 11 to upper right headboard using bold F and G and allen key M , as shown. I GG++MM To help prevent serious or fatal injuries from Warning entrapment or falls: Strangulation Hazard: Never attach or hang items to any part of the bunk bed that are not designed for use with this bed; for example, but not limited to, belts, bags, ropes and clothing.
Assembly Instructions Step 9 F Fixing long guard rails Fix long guard rail 8 to upper right headboard 1 and upper left headboard 2 using screws F and allen key M . M M+ F M+ F 8 8 F +M F +M 2 1 Step 10 Fitting upper bed Two people are required for this step 2 Insert barrel nut K and connector bold L into the Lower bed. Then, insert metal pin J into the Lower bed, as shown. K L J Insert barrel nut K into upper bed. Then, with care, attach the two beds through metal pin, as shown.
Assembly Instructions Step Step1111 Firstly, fix slats 12 on both ends of the rails using screws C , as shown. ! 60 - 72mm Fixing slats N I 1º 12 a: N I 13 12 13 Using Spacer N , place slats 13 working towards the middle of the bed, as shown. b: 1º Fix on the side first, using screws C , then fix other side by pushing the rail against the slats if necessary.
Assembly Instructions Step 12 MATTRESS HEIGHT MUST NOT BE ABOVE THIS LINE Attaching ladder 5 to short ladder Fit steps 5 14 side rail 14 and long ladder 15 side rail 15. M+H Fix steps to the rail using M . H and allen key m bolt h 15 M+H M+H 05 14 05 H +M 05 H H +M +M Step 13 Fixing ladder Fix ladder to the side rails using bolt H and allen key M , as shown.
Assembly Instructions Step 14 M+ H Fixing short guard rail M+ H F Attach wooden dowels B to the indicated holes of the ladder, as shown. B Fix short guard rails 9 to upper left headboard 2 using bolt F and allen key M ,and to the ladder using M bolt Hh and allen key m. 09 09 M+ F 2 M+ F Step 15 Fixing guard rail support Fix guard rail support 4 to long guard rails 8 and side rail using screws D , as shown.
Assembly Instructions Step 16 Attaching plastic caps Fit plastic caps O into the indicated holes on both upper and lower beds, as shown. O O O O O O O O Step 17 Attaching plastic caps Fit plastic caps R into the indicated holes on both upper and lower beds, as shown.
Assembly Instructions Step 18 Turning bunk bed into two single beds Q Detach ladder from the bunk bed and remove the upper bed from top of the lower bed. Detach guard rails from the upper bed.
Assembly Instructions Step 20 Attaching plastic caps Fit plastic caps Q and P into the indicated holes,as shown. Q Q Q 02 Q Q Q Q 11 Q Q Q Q P Q P 10 P 01 P Step 21 Attaching plastic caps Fit plastic caps R , O , and P into the indicated holes, as shown. O O O O 03 O O O R R O 11 R R P 10 03 P R R P P R R Assembly is complete.
15
