Desk Assembly Instructions - Important: Retain these instructions for future reference 280/0332 247/7167 238/3615 246/5818 268/6965 478/9444 565/7135 275/6297 274/6616 462/7290 246/4950 WARNING! 501/2127 278/6652 NOT SUITABLE FOR CHILDREN UNDER 6 YEARS OF AGE 497/1757 247/3848 462/7434 459/4581 820/1100 WARNING! In order to prevent overturning, this product must be used with the 2 wall attachment devices provided Dimensions Width - 120cm Depth - 49cm More help is available throughout this booklet by
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 24kgs. Please lift with care. • Parts of the assembly will be easier with 2 people. • Assembly to be carried out by a competent adult only. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below 1 Left Side (D2785D) (70.6 x 35.3cm) 2 Right Side (D2786D) (70.6 x 35.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 Prepare the 3 drawer fronts Screw 2 metal dowels B into each of the drawer fronts 8 . Drawer Assembly www.youtube.com/watch?v=InNBV_uuMmo B B B 8 Note: Tighten the metal dowels up fully against the panels. x3 Step 2 Prepare the drawer sides Insert a small locking cam nut F into the hole shown on the left drawer side 9 and the right drawer side 10 . F F F 10 9 x3 Note: The arrow on the locking cam nut must point towards the hole in the edge of the panel.
Assembly Instructions Step 4 Fit the drawer base 12 Slide the drawer base 12 down the grooves in the drawer sides 9 and 10 and down into the groove in the drawer front 8 . x3 10 9 8 Step 5 Fit the drawer back Fit the drawer back 11 between the drawer sides 9 and 10 . Make sure that the drawer base 12 fits into the groove in the drawer back 11 . Hold the drawer back 11 in position and tap the knock-in pegs N through the holes in the drawer sides 9 and 10 .
Assembly Instructions Fitting Ball Bearing Runners www.youtube.com/watch?v=yG4xtiJJeSg Step 8 Prepare the left side b: Slide the runner J back the other way and fit the 2nd screw K into the corresponding hole in the left side 1 . Insert 2 large locking cam nuts E into the left side 1 . K Finished front edge a: Place 3 runners J on the left side 1 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw K .
Assembly Instructions Step 9 Prepare the right side Finished front edge K J a: Place 3 runners J on the right side 2 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw K . b: Slide the runner J back the other way and fit the 2nd screw K into the corresponding hole in the right side 2 . J K J 2 Finished front edge E Insert 2 large locking cam nuts E into the right side 2 .
Assembly Instructions Step 11 Fit the plinth and the rail to the right side Push the plinth 6 onto the right side 2 and secure it with screw G . G 2 G Note: Support the rail until the left side has been fitted in the next step. 7 Push the rail 7 onto the right side 2 and secure it with screw G . Finished top edge 6 Main unit colour Step 12 Fit the left side Push the left side 1 onto the unit and secure it with 2 screws G .
Assembly Instructions Step 14 Squaring up a Chest and fitting the Back Panel www.youtube.com/watch?v=FeaI6541z7o Fit the back a: Square up the unit by making sure that measurement x to x equals y to y. b: Place the back a: The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y b: 13 down onto the unit, making sure that it is flush with the bottom of the rail 7 . Nail C down the sides and along the bottom edge of the back 13 .
Assembly Instructions Step 16 G Fit the shelves to the bookcase ends Attach the 3 shelves 5 to the bookcase ends 3 using 12 screws G . G G inside surface G 3 G 5 G 5 5 p chi lain pb sur oard fac e p chi lain pb sur oard fac e p chi lain pb sur oard fac e 3 G G G G G G Step 17 Fit 4 plastic nails Tap 2 plastic nails I into the bottom edge of each bookcase end 3 as shown.
Assembly Instructions Step 18 Choose desk layout Before going onto the next step, decide which way around you would like your desk to be. Place the 2 assemblies where the desk will be used, so that the unit does not have to be moved once the top panel has been secured into place. Drawers on the left Drawers on the right Step 19 B B Prepare the top B Screw 8 metal dowels B into the top 4 .
Assembly Instructions Step 20 Fit the top Lift the top 4 and push the 8 metal dowels B fitted to the top 4 down into the holes in the top edge of the sides and bookcase ends 1 , 2 and 3 . 4 3 Use a screwdriver to tighten the 8 large locking cam nuts E fitted to the sides and bookcase end panels 1 , . 2 and 3 . 3 2 1 Note: Turn the large locking cam nuts E as far as they will go - more than 1/2 a turn.
Assembly Instructions Step 21 Fit the 2 overbalance protector kits To prevent possible overbalancing this unit must be secured to a suitable wall by fitting of the 2 overbalance protector kits O , 1 at each side the unit. Wall fixings are not supplied as they will need to suit the wall type. Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
A Guide to Wall Mounting & Fixings Important: When drilling into walls always check that there are no hidden wires or pipes etc. Important note: If plastic wall plugs are supplied with your product: Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualifed tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
Assembly Instructions Step 22 Fit the drawers Fitting Ball Bearing Runners www.youtube.com/watch?v=yG4xtiJJeSg Starting with the bottom drawer, slide both the runners J forward and locate the drawer sides 9 and 10 between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners J . Working from the inside of the drawer, insert 2 screws L through the drawer sides and out into the 2nd threaded hole in the runner. L L 10 9 Assembly is complete Warning: The unit is heavy.
