JENSON Gloss 891/7944 889/2416 Spare Parts Customer Support Visit: www.argos-support.co.uk Call: 0345 640 2020 Email: Help@ClickSpares.co.
Safety Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 50kgs. Please lift with care. • During assembly children should be kept away from the product due to possible risk of injury. • Installation shall only be carried out exactly according to the manufacturer’s instructions otherwise a safety risk can occur if incorrectly installed. • Do not use this item if any components are missing or damaged.
6 42.3 x 41.5cm 12 57.2 x 39.6cm 42.3 x 41.5cm 58.3 x 6.0cm x 4 7 57.2 x 41.4cm 9 1779.0 x 36.5cm 10 180.2 x 45.0cm 11 58.3 x 39.6cm x 13 59.6 x 32.7cm x 4 8 2 DF-00022846 DF-00022917 DF-00022844 DF-00022843 XDF-00022850 5 DF-00022848 DF-00022452 3 58.3 x 41.4cm x 2 DF-00022915 42.3 x 42.9cm DF-00022920 2 DF-00022453 42.3 x 42.9cm DF-00022847 1 Please do NOT remove any protective film until after assembly DF-00022450 DF-00022449 Cabinet Panels 3 57.2 x 6.
Fittings Use these drawings to correctly identify the fittings D x 16 x8 x8 E I x6 F110 F x 12 J x8 K x8 F474 F328 H F40 F566 F22 x 16 F51 C F63 x9 x 16 F646 G B F137 x 32 F639 A F901 F900 Bag 1 L x2 M x6 Tools Only used for drilling walls
1 C x4 Finished front edges 2 1 2 A x4 2 1 3 B x8 2 1
4 A x2 C Finished front edge x2 3 5 A x4 C x2 Finished front edge 4
6 x2 1 4 Finished front edge Finished front edge 7 A x4 C x2 5 5
x2 4 5 5 9 F E x4 D 3 Finished front edge
10 x2 D x4 3 x2 11 A x2 C x2 6 Finished front edge
12 A x4 7 Finished front edge 13 7 Finished front edge x2
14 A x4 8 8 15 8 8 x2
16 E x4 6 Finished front edge 17 x2 D x4 6 x2
18 A x4 C x2 Finished front edge 4 19 x2 4 Finished front edge
20 A x4 C x2 5 5 21 5 5 x2
22 2 x2 Finished front edge 23 J x8
24 9 25 Squaring up a Chest and fitting the Back Panel www.youtube.com/watch?v=FeaI6541z7o The Back panels must be flush with the Base. A=B Make sure the measurements are the same.
26 H x 16 9 27 B x8 L x2 Only use 1 Screw to fit each Bracket 11 Finished front edge
28 x8 10 IMPORTANT: The Back panel must slot into the groove in the Top panel 29 G x9 Finished front edge
30 WARNING! In order to prevent overturning this product must be used with the 2 wall attachment devices provided See the next section for a guide to wall mounting and fixings Top Slide the Brackets against the wall. Fit the 2nd screws supplied with the Brackets into the underside of the Top panel. Mark the slot at the back of the Brackets for drilling into the wall. Wall fixings are not supplied as they will need to suit the wall type.
A Guide to Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
31 F x12 32 11 12 11 Finished front edge
33 K x8 M x6 Pre-mounted Hinge Fitting & Adjustment https://www.youtube.
35 Pre-mounted Hinge Fitting & Adjustment https://www.youtube.com/watch?v=b4NeCGnpjP8 Adjust the Door if required a: a: Height adjustment. Loosen screws A on Hinge Plates and move Door up or down as required. Retighten screw A. b: Forward and Back adjustment. A A b: Loosen screw B on Hinge Plate and move door in or out as required. Retighten screw B. B c: c: Sideways adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
37 Assembly is complete Please remove any blue protective film from panel edges and clear protective film from panel surfaces ALR3718