DR8250800 Bergen 180 High gloss doors Assembly Instructions- Please keep for future reference 518/9696 517/9101 High gloss doors 1 1 2 2 1 1 Dimensions Width - 180cm Depth - 6.7cm Height - 195.2cm Tip : To prevent damage, we recommend that you build your unit on the carton(s) it was packed in. Dimensions 518/9696 WHITE HG 517/9101 CAHMERE HG Important – Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit: www.
Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible. • Keep children and animals away from the work area, small parts could choke if swallowed.
Components - Panels For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk Please check you have all the panels listed below Cabinet supplied separately 249/4834 248/6921 226/8730 1 Segment x4 (91.5 x 65cm) P3355 2 Segment middle x2 (91.5 x 65.
Components - Fittings For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. FK1309 D Screw x 72 (4x12.
Assembly Instructions Step 2 a: E 3 Segment slide door left E a: Put 8x nylon plug E into the segment 1. Use a small hammer. Repeat this step. 1 2x b: Mount door trim U with 3x screws D on segment 1. D D b: D 1 Note: there should be no gap between doorsegment 1and door trim U. U No Gap between metal profiles and door panel! c: Mount segment middle 2 with 3x screws D on door trim U. Mount segment 1 with 4x screws D on door trim U.
Assembly Instructions Step 2 See page 2 for link to instruction video! e: 3 Segment slide door left e: Mount 4x connecting plate O, each with 2x screws D on segment 1 and 2x screws D on middle segment 2. Remove protective film from door handle S. Stick 1x brush T onto door handle S by partially removing the cover from adhease as brush is applied. D 1 D D O T D O D 2 D O D O T Please remove the protective film! 1 S S AC f: Upside.
Assembly Instructions Step 3 See page 2 for link to instruction video! Place left slide door 2 People are required for step 3a and 3b. a: a: Hook the 2x back guide part j into the plastic guide rail R. 1 2 1 R a: Detail.
Assembly Instructions Step 3 Place left slide door b: Hook Sliding door connecting platek on metal guide rail Q. Q b: 1 2 1 b: Detail. The wheel of the sliding door connecting plate k should be in the front guide of the metal guide rail Q. To lock the door, lock the Sliding door connecting plate k on the guide railQ with the locking pawl.
Assembly Instructions Step 4 3 Segment slide door right E a: Put 8x nylon nylo plug E into segment 1. the Usesegment the a small hammer. 3. Repeat Use a small this step. hammer. Repeat this step. b: Mount door handle S with 4x screws D on segment 3 1 .. a: E 2x 1 D D b: D D 1 Note: there should be no gap between doorsegment 1 and 3 and door door handle handle S. S. (see m). S No Gap between metal profiles and door panel! c: Mount segment middle 4 with 3x screws D on 2 door handle S.
Assembly Instructions Step 4 e: 3 Segment slide door right e: Mount 4x connecting plate O, each with 2x screws D on segment 3 and 2x screws D on middle segment 4. Remove protective film from door handle S. Stick 2x brush T onto 2x door handle Sby partially remove the cover from adhease as brush is applied. See page 2 for link to instruction video! T 1 D D O D D 2 D O T Please remove the protective film! T D O D O D 1 S S f: Upside.
Assembly Instructions Step 5 See page 2 for link to instruction video! Place right slide door a: Hook the 2x front guide part i into the plastic guide rail R. a: 1 2 1 R a: Detail.
Assembly Instructions Step 5 a: Place right slide door b: Hook the sliding door connecting bracketl on metal guide rail Q. Q 1 2 1 b: Detail. The wheel of the sliding door connecting bracket l should be in the rear guide of the metal guide rail Q. To lock the door, lock the sliding door connecting bracket l on the guide rail Q with the locking pawl.
