JENSON Gloss 937/8032 922/8058 Spare Parts Customer Support Visit: www.argos-support.co.uk Call: 0345 640 2020 Email: Help@ClickSpares.co.
Safety Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 56kgs. Please lift with care. • During assembly children should be kept away from the product due to possible risk of injury. • Installation shall only be carried out exactly according to the manufacturer’s instructions otherwise a safety risk can occur if incorrectly installed. • Do not use this item if any components are missing or damaged.
4 10 67.7 x 48.3cm 7 47.1 x 41.4cm 12 48.2 x 39.6cm x 8 47.1 x 6.0cm x 11 149.9 x 45.0cm DF-00023781 DF-00023785 2 2 13 2 DF-00023783 67.7 x 49.3cm x 2 47.1 x 39.6cm DF-00023778 9 48.2 x 41.4cm x XDF-00023791 48.2 x 6.0cm x XDF-00023780 5 4 DF-00023782 73.3 x 41.5cm 73.3 x 41.5cm DF-00023786 DF-00023787 6 3 DF-00023777 73.3 x 42.9cm DF-00023784 2 DF-00023789 73.3 x 42.
Fittings Use these drawings to correctly identify the fittings x 10 J x4 E x 10 F K x 13 F276 F277 F40 x8 G x4 F63 D x8 L x 12 F474 F328 I F566 F22 x 22 F646 x 12 C F137 H x 16 B F639 x 32 F110 A F901 F900 Main Bag M x2 N x6 Tools Only used for drilling walls
1 I x 10 D x8 E J x4 x 10 F K x8 F276 F40 F566 F22 x 22 x 13 G F63 x 12 C F646 H x 16 B F137 x 32 F639 A F901 F900 x6 F110 C F277 Main Bag L x 12 2 Finished front edges 1 2 A x4 2 1 x4
3 B x8 2 1 4 A x2 C Finished front edge x3 3 5 A x4 C x3 4 Finished front edge
6 x2 1 4 Finished front edge Finished front edge 7 A x4 C x2 5 5
x2 4 5 5 9 F E x5 D 3 Finished front edge
10 x2 x4 D 3 x2 11 A x2 C x3 6 Finished front edge
12 A x4 7 Finished front edge 13 3 7 Finished front edge x2
14 A x4 8 8 15 8 8 x2
16 E x5 6 Finished front edge 17 x2 D x4 6 x2
18 A x4 C x3 4 Finished front edge 19 4 Finished front edge x2
20 A x4 C x2 5 5 21 5 5 x2
22 x2 2 x2 Finished front edge 23 K x8
24 9 10 9 25 Squaring up a Chest and fitting the Back Panels www.youtube.com/watch?v=FeaI6541z7o The Back panels must be flush with the Back Rail. A=B Make sure measurements are the same.
26 IMPORTANT: You will need to keep 4 nails for the next step F x9 9 10 9 27 F x4 G x4 9 10 9
28 B x8 M x2 Only use 1 Screw to fit each Bracket 11 Finished front edge 29 Finished front edge 11 IMPORTANT: The Back panel must slot into the groove in the Top panel
30 I x 10
31 WARNING! In order to prevent overturning this product must be used with the 2 wall attachment devices provided See the next section for a guide to wall mounting and fixings Top Slide the Brackets against the wall. Fit the 2nd screws supplied with the Brackets into the underside of the Top panel. Mark the slot at the back of the Brackets for drilling into the wall. Wall fixings are not supplied as they will need to suit the wall type.
A Guide to Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
32 H x12 33 12 13 12 Finished front edge Finished front edge Finished front edge
34 L x 12 M x6 Pre-mounted Hinge Fitting & Adjustment https://www.youtube.
36 Pre-mounted Hinge Fitting & Adjustment https://www.youtube.com/watch?v=b4NeCGnpjP8 a: Adjust the Door if required a: Height adjustment. Loosen screws A on Hinge Plates and move Door up or down as required. Retighten screw A. A A b: Forward and Back adjustment. Loosen screw B on Hinge Plate and move door in or out as required. Retighten screw B. b: c: Sideways adjustment. B To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
