Jenson Mirror 940/0371 Spare Parts Customer Support Visit: www.argos-support.co.uk Call: 0345 640 2020 Email: Help@ClickSpares.co.
Safety Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 34kgs. Please lift with care. • Assembly to be carried out by a competent adult only. • During assembly children should be kept away from the product due to possible risk of injury. • Installation shall only be carried out exactly according to the manufacturer’s instructions otherwise a safety risk can occur if incorrectly installed.
Cabinet Panels 2 XDF-00022219 137.1 x 28.8cm 3 135.3 x 58.7cm 5 55.6 x 35.5cm 7 54.9 x 14cm x6 8 54.9 x 8.7cm x3 59.5 x 29cm 56.1 x 5.8cm DF-00022244 4 x3 6 DF-00022241 DF-00023102 DF-00023802 137.1 x 28.
WRP-00000474 10 26 x 6.8cm 55.6 x 9.6cm 11 26 x 6.8cm TDF-00022552 WRP-00000475 9 WRP-00000473 Note: the internal drawer panels are grey DF-00023808 Drawer Panels 12 52.85 x 6.8cm 13 53.95 x 25.
Fittings Use these drawings to correctly identify the fittings x 16 A A B x 16 C x 16 D F646 F51 F73 F22 F900 F901 Bag 1 x4 E x 25 F x4 G x4 H I x2 M F464 x4 F506 F63 F52 x 24 J K x5 Bag 4 Bag 3 L F171GY F74 x2 x 18 N F109 x2 F507 A A F3 F901 F639 Bag 2 x6 O x6 P x6 F52 F259 F258 Bag 5 L x2 Q x1 R x1
Fittings Shoe Boys a b c c d e e c x3 F474 S d F307 d FST e T x2 U x2 Tools Only used for drilling walls
1 A A U x 16 x 16 C x 16 F51 F73 F900 B F22 x4 D x4 E x 25 x2 A 2nd hole B Finished front edge 2 1 Finished front edge A 2nd hole B F646 Bag 1 F901 D Fitting Ball Bearing Runners www.youtube.
2 C x4 2 1 3 B x4 2 4 1 A x 12 2 1
5 x6 N F507 F506 N F109 Bag 4 x6 O x6 P 2 1 6 e S x6 Shoe Boys IMPORTANT: Carefully snap off these fittings from the Shoe Boys a b c e e d c S 2 1 x3 d x6
7 5 C x 12 B x 12 x6 Finished front edge 8 Finished front edge 5 5 1 Finished front edge 5 Finished front edge Finished front edge 5 5 5 Finished front edge 9 x2 IMPORTANT: Support panels until other end panel is fitted in the next step 5 5 1 5 Finished front edge 5 5 x4 5
10 x2 2 x4 Finished front edge 11 4 A x4 12 Finished front edge Only use 1 Screw to fit each Bracket T x2 4
13 F259 x2 Q F52 L x1 L 4 14 x4 4 Finished front edge F258 Bag 5 x2 Q x1 R x1
15 Squaring up a Chest and fitting the Back Panel www.youtube.
17 F x4 3 ‘Tap’
18 WARNING! T In order to prevent overturning this product must be used with the 2 wall attachment devices provided x2 Top 3 See the next section for a guide to wall mounting and fixings Slide the Brackets against the wall. Fit the 2nd screws supplied with the Brackets into the underside of the Top panel. Mark the slot at the back of the Brackets for drilling into the wall. Wall fixings are not supplied as they will need to suit the wall type.
A Guide to Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
19 x6 O N F507 x6 F506 P x6 O 6 x3 20 Shoe Boys a b c c d e e d c S d x3 d FST e c x6 Warning: Glass! Handle with care Shaped front edge F109 Bag 4 IMPORTANT: Carefully snap off the rest of the fittings from the Shoe Boys to use later P x6
21 b L L x9 S x 24 x3 6 x3 22 8 23 x3 Finished front edge M x3 8 x3 F63 F52 Bag 3 M x 18
24 Finished front edge 7 x3 25 M x3 7 x3 IMPORTANT: Support this panel until the Shoe Boy is fitted in the next step 26 a L x9 S x3 x3
27 M x6 x3 28 d L x6 S x6
29 c S x6 Door Stop IMPORTANT: Lift and position the Doors so that the Door Stops are fitted between the 2 lugs at the top of the Shoe Boys
30 Slot the Divider panels down into 1 of the 3 positions shown 7 7 7 Finished front edge Finished front edge Finished front edge
31 32 M x6 Drawer Push adjustment. Finely adjust the Magnetic Catches to suit your requirements. Just a 1/4 of a turn can make a difference.
Drawer Assembly A A x2 G x4 H x2 I x2 J x4 F464 F171GY F74 F3 F901 F639 Bag 2 K x5 Standard Drawer Box Assembly https://www.youtube.
36 x2 10 11 9 37 13 Ensure the drawer base sits flush by turning the shelf studs clockwise or anti-clockwise
38 J x4 12 39 G x4
40 I Fitting Ball Bearing Runners www.youtube.com/watch?v=yG4x�JJeSg x2 Warning: Use a screwdriver to position the runners as they could have sharp edges Slide both the runners forward and locate the drawer sides between them, lining up the holes in the drawer sides with the 2nd 'threaded' holes in the runners. Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner. Note: Do not overtighten the screws.
41 R 42 x1 Adjust the Drawer Push Finely adjust each Door Push to suit your requirements. Just a 1/4 of a turn can make a difference.
