Installation Sheet

ManualsBrandsHager ManualsMortise LocksHager Grade 1 Double Stainless Steel Dummy Lever Handle Set for 3800 Escutcheon Mortise Collection

3800 Series Mortise Lock - Escutcheon

Installation Instructions

I-LS00125

DEVICES COVERED IN THIS DOCUMENT:

3800 Series Mortise Lock - Escutcheon Model

OVERVIEW

REV 2

Page 1 of 4

Inside Cylinder

Cylinder Turn

Inside Escutcheon

Mounting Screws

Inside Lever or Knob

Inside Escutcheon with Thumbturn

Inner Spring Insert Assembly

Armor Front

Mounting Screws

Lock Case

Outer Spring Insert Assembly

Outside Escutcheon Assembly

Outside Lever

or Knob

Emergency

Button

Thru-bolts

Spindle

Spring Insert Screws

Inner Escutcheon Insert

Spindle

Outside

Cylinder

Mounting Screws

Strike

Strike Box

Escutcheon

with

Coin Turn

50, 53, 56, 73, 81

65, 70, 76, 80

57, 61, 66, 82, 83

10, 77

40, 41

44, 45

1, 2, 3, 4, 5, 6, 7, 9, 12, 13

1, 2, 3, 4, 5, 6, 9, 12, 13

1, 2, 3, 4, 5, 6, 9, 10, 12, 13

1, 2, 3, 4, 5, 6, 9, 11, 12, 13

FUNCTION INSTALLATION STEPS

STEP 1: PREPARE DOOR AND JAMB

A. Mark lockset centerline of lever.

i. Measure desired height from finished floor.

ii. Mark centerline on both faces and edge of door.

NOTE: If mortise for strike has already been made, measure 1-7/8” down from center of strike to locate

center line of lever.

CAUTION: The outside and inside of door may require different preparation. Use proper template for

outside (exterior or corridor) and inside of door.

B. Mark trim drill points.

i. Align centerline of door template with centerline marked on door edge.

ii. Based on the function of the lock, mark position of drill points.

C. Mortise door edge (for wood doors).

i. Align template with centerline of door edge.

ii. Mark and drill two (2) 1” diameter holes, 4-1/2” deep.

iii. Remove remaining wood until the mortise is 1” wide, by 6-3/4” high, by 4-1/2” deep.

of Lever

Height Line

of Cylinder

of Lever

6 3/4"

of Door Edge

of Cylinder

of lever

1" drill 4 1/2" deep

Summary of content (4 pages)

PAGE 1
3800 Series Mortise Lock - Escutcheon Installation Instructions I-LS00125 DEVICES COVERED IN THIS DOCUMENT: 3800 Series Mortise Lock - Escutcheon Model OVERVIEW FUNCTION INSTALLATION STEPS 1, 2, 3, 4, 5, 6, 7, 9, 12, 13 1, 2, 3, 4, 5, 6, 7, 9, 12, 13 1, 2, 3, 4, 5, 6, 7, 9, 12, 13 1, 2, 3, 4, 5, 6, 9, 12, 13 1, 2, 3, 4, 5, 6, 9, 10, 12, 13 1, 2, 3, 4, 5, 6, 9, 11, 12, 13 50, 53, 56, 73, 81 65, 70, 76, 80 57, 61, 66, 82, 83 10, 77 40, 41 44, 45 Inside Lever or Knob Inside Escutcheon with Thumbturn Insid
PAGE 2
3800 Series Mortise Lock - Escutcheon Installation Instructions I-LS00125 STEP 1: PREPARE DOOR AND JAMB (cont) D. Drill trim holes. NOTE: To prevent splintering or damaging doors, drill through-holes halfway from each side of door. 7/32" E. Create a recess for the lock face. The standard recess is 1-1/4” x 8” x 7/32”. F. Install strike. i. Align centerline of strike template with the centerline marked on doorjamb. Be sure to match centerline on both strike and lock trim templates. ii.
PAGE 3
800 Series Mortise Lock - Escutcheon Installation Instructions I-LS00125 STEP 3: INSTALL OUTER INSERT ASSEMBLY SKIP STEP “A” FOR THE FOLLOWING FUNCTIONS: 80, 81, 82, 83. SLOTTED SPINDLE IS NOT REQUIRED FOR THESE FUNCTIONS. A. Insert outer spindle into lock hub (short end of slotted spindle must be placed toward lock case). B. With lever keeper toward door edge, place insert assembly over spindle. C. Insert thru-bolts into appropriate holes in insert according to handing of door.
PAGE 4
3800 Series Mortise Lock - Escutcheon Installation Instructions I-LS00125 STEP 9: INSTALL ARMOR FRONT A. Secure cylinder by tightening cylinder anchor screw until hand-tight. B. Tighten two (2) lock case mounting screws. C. Place armor front in position and install two (2) screws. A B C STEP 10: INSTALL EMERGENCY BUTTON A. Snap emergency button into place. Emergency Button STEP 11: INSTALL COIN TURN A. Insert coin turn in the vertical position.