Twin-tub Washing Machine With Pump This manual is for Please read this manual carefully before using. Retain it for future reference.
Contents Names of the parts Safety precautions Installation and adjustment Preparation before washing The musts in washing Usage of the detergent Washing sequence Disposal after washing Trouble-Shooting *Answers to question Packing list *Specification
Names of the parts Water-filling entrance Outer cover of the spin tub Water inlet selector handle Inner cover of the spin tub Buzzer Spin timer Wash selector Wash timer Spin tub frame Control panel Spin tub Filter frame Cabinet Lint filter Power cord Wash tub Pulsator Drain hose Wash tub cover Base frame Notes: All illustrations in this Manual are given for reference only. Your products and accessories may show differences from these illustrations due to our continuous improvement.
Safety precautions Please insert the power cord into special receptacle with rated voltage.Be sure to use single-phase three pins receptacle.The earthing terminal of the receptacle must be earthed reliably.If possible,please adopt electric leakage protector. When the machine is normally using, please put the power plug at the location easily to be inserted and extracted by hand. Be sure to pull the plug off when there's power failure, or the machine is being moved, cleaned or when it is idle.
Safety precautions Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the machine by yourself. rotation is slow. Take special care of the children. Do not put any hot or heavy items ( such as the kettle with hot water ) on the washing machine. Do not wash laundries with volatile materials (such as thinner, petrol etc.). l Petro Handicapped or children without care shall not use the machine.
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter Put the underside of the lint filter into overflow filter then push the upside into overflow filter After installation,please refer that the lint filter installed to the right station,otherwise the lint filter may be falled off when washing,influencing your use.
How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Back Extend the drain hose from the side of spin tub Soft item Front Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. Take off the drain hose from the cabinet. Dismantle the drain hose fixing clamp and take the hose out of the fixing groove. (See to Figure 2).
Introduction of the major function This washing machine has been provided with excellent washing performance and luxury appearance,paeticularly for safeguard during washing. In order to give you a quiet and comfortable washing,enclosed base frame and lower -noise motor have been designed to reduce the noise.With Haier machine, we believe that it is the right choice for your everyday.
Preparation before washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put up the drain hose . <1.2m 4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally.
The musts in washing The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.The largest capacity of this machine is 10.0kg The thickness ,size , type of the cloth will influence the actual washing capacity.
Washing sequence Water-filling selector Wash timer Wash selector (To set to below 2 minute, first set to 5 minute then turn it back. it can increase the service life of the timer). OFF SILK (standard current, strong current) Buzzer Water-filling entrance Spin timer (The buzzer will ring when the washing finishes) (to set to below 1 minute, first set to 2 minute then turn it back. it can increase the service life of the timer).
Midway spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Push Proper The laundries are slanting Proper No gland (2) Close the inner and outer cover of the spin tub. Outer cover of The spin tub Inner cover of (3) Spin for 1-2 minutes. The spin tub 3.Run the foam-removing spinning. 1 Set the inlet selector handle on spin side and fill water for about 1 min.
Rinsing Rinse with water-filling OVERFILL 1.Put the laundries into the wash tub. Select suitable current according to the laundries. 2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously. If you find water flowing out here,please twist the water tap to limit the water filling. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing.
12
Disposal after washing After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing. It must be cleaned in time after each using. 1. Press the elastic piece at upper end of lint filter to release the tab from the filter cover, and pull the lint filter outward to remove it.
Cleaning the overflow filter 2. Take off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1). Water level adjusting lever Corrugation Pipe 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water. 4. Install the overflow filter. (1).Install the corrugation pipe. (2).Insert the mounting plate at the bottom of the filter into the valve cover. (3).Hang up the hook at the left upper side. (4).
Trouble-shooting Answers to question When the remained water is frozen Prevent the freezing (be sure to discharge the water completely after using) After complete draining, set the "WASH SELECTOR" at STRONG or STANDARD . If it is set at "DRAIN", it will be rather difficult for the frozen water to melt. When the water is frozen Pour hot water below 50 into the wash tub to soak it completely. Then turn the pulsator with hands gently. Please confirm the drainage can work normally before next using.
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomena The machine does not act.
Packing list Quantity Name User's manual One piece Water inlet hose One piece One piece Gland Twin-tub washing machine One set Specification Water level Water quantity about Maximum/99L Medium/77L Minimum/65L Rated washing capacity kg 10.0 Rated spinning capacity kg 6.0 Injection pressure 17 0.02MPa~0.