Installation guide

ManualsBrandsHaier ManualsAir ConditionersAir Conditioner Cooling Area,

Ductless S plit Air Conditioner

Indoor

AW09ES2VH*

AW12ES2VH*

AW18ES2VH*

AW24ES2VH*

AW09TE1VH*

AW12TE1VH*

AW18TE2VH*

AW24TE2VH*

Outdoor

1U09ES2VHA

1U12ES2VHA

1U18ES2VHA

1U24ES2VHA

1U09TE1VHA

1U12TE1VHA

1U18TE2VHA

1U24TE2VHA

Installation M anual

Step 1 - Preparation ...................................................................................................................... 2

Step 2 - Installation of the Indoor Unit ........................................................................................... 3

Step 3 - Installation of the Out door Unit........................................................................................ 4

Step 4 - Interconnecting the Indoor and Outdoor Units ................................................................. 5

............................................................................................. noitaucavE dna tseT kaeL - 5 petS .....6

Step 6 - Char ging ...........................................................................................................................7

Section 7 - Explaining Operation to the End User ........................................................................... 8

.................................................................................................. 8

Section 9 - S

0010586612

eacoast Application ................................................................................................... 8

Table of Contents

Summary of content (10 pages)

PAGE 1
Ductless S plit Air Conditioner Installation M anual Indoor AW09ES2VH* AW12ES2VH* AW18ES2VH* AW24ES2VH* AW09TE1VH* AW12TE1VH* AW18TE2VH* AW24TE2VH* Outdoor 1U09ES2VHA 1U12ES2VHA 1U18ES2VHA 1U24ES2VHA 1U09TE1VHA 1U12TE1VHA 1U18TE2VHA 1U24TE2VHA Table of Contents Step 1 - Preparation ...................................................................................................................... 2 Step 2 - Installation of the Indoor Unit ...............................................................
PAGE 2
Step 1 - Preparation Procedure for Selecting the Location ENGLISH Required Tools for Installation Note: detector place. Clearances of Indoor and Outdoor Units The models adopt HFC free refrigerant R410A Attention must be paid to the pitch of drain hose more than 4in. Floor xing dimensions of the outdoor unit (Unit: inch) more than 4in. Z G 1 Arrangement of piping directions Model more than 4in. F Rear left A Rear right Left Right C Below more than 4in. more than 4in.
PAGE 3
Step 2 - Installation of the Indoor Unit Attaching the Mounting Plate to the Wall ENGLISH 2.1 Step 2.1 Using a stud sensor, locate and mark the stud positions in the wall where the indoor unit is to be mounted. 2.2 Step 2.2 Place the mounting plate on the wall in the desired location taking into account the minimum clearances necessary for proper operation. Step 2.1 Step 2.2 Step 2.3 Step 2.4 Step 2.5A Step 2.5B Step 2.6 Step 2.7 Step 2.8A Step 2.
PAGE 4
Mounting the Indoor Unit Onto the Wall Plate ENGLISH 2.9 Step 2.9 With the top of the indoor unit closer to the wall, hang the indoor unit on the upper hooks of the mounting plate. Slide the unit slightly side to side to verify proper placement of the indoor unit on the mounting plate. Rotate the lower portion of the indoor unit to the mounting plate, and lower the unit onto the lower hooks of the mounting plate. (Illustration 2) Verify the unit is secure. 2.10 Step 2.10 Step 2.9 Step - 2.
PAGE 5
3.3 Step - 3.3 3.4 Step 3.3 ENGLISH Connect the wiring for both the power source and indoor wiring. Wire the system according to applicable national / local codes. Verify that the wiring connections for the indoor unit match wire for wire. (1-1, 2-2, 3-3, Gnd-Gnd). Failure to wire the system correctly may lead to improper operation or component damage. Step 3.4 Step - 3.4 Replace the cover plate. Step 4 - Interconnecting the Indoor and Outdoor Units *See Steps 2.11 - 2.13 & 3.2 - 3.
PAGE 6
Step 5 - Leak Test and Evacuation ENGLISH Leak Test * $
PAGE 7
piping hole. Use a sealant to seal the piping hole opening to prevent weather elements from entering the building. (Illustration 6) It becomes The end is imm- It waves. The gap with the There is the bad high midway. ersed in water. ground is too small smell from a sewer Illustration 6 Step 6 - Charging See Steps 5.2 - 5.5 for evacuating the system prior to charging. The standard lineset length is 25ft.
PAGE 8
Section 7 - Explaining Operation to the End User for operation, etc.) ENGLISH ATING INS TRUC TIONS carefully .
PAGE 9
[This page intentionally left blank.
PAGE 10
www.Haier.com Model #: 1U09ES2VHA, 1U12ES2VHA 1U18ES2VHA, 1U24ES2VHA AW09ES2VH*, AW12ES2VH* AW18ES2VH*, AW24ES2VH* AW09TE1VH*,1U09TE1VHA AW12TE1VH*,1U12TE1VHA AW18TE2VH*,1U18TE2VHA AW24TE2VH*,1U24TE2VHA Issued Date: Jan 2017 Update Haier America, Wayne, NJ 07470 ©2017 Haier America Trading, LLC.