Installation guide

ManualsBrandsHaier ManualsAir HandlerOfficial Haier room air conditioner

Ductless Split Air Conditioner

Installation Manual

Step 1 - Preparation ...................................................................................................................... 2

Step 2 - Installation of the Indoor Unit ........................................................................................... 3

Step 3 - Installation of the Outdoor Unit ........................................................................................ 4

Step 4 - Interconnecting the Indoor and Outdoor Units ................................................................. 5

Step 5 - Leak Test and Evacuation .................................................................................................. 6

Step 6 - Charging ........................................................................................................................... 7

Section 7 - Explaining Operation to the End User ........................................................................... 8

.................................................................................................. 8

Section 9 - S

0010590560

eacoast Application ................................................................................................... 8

Table of Contents

Indoor

AS09TB1HRH

AS12TB1HRH

AS15TD1HRE

AS18TD1HRE

AS24TE1HRE

Outdoor

1U09BU1ERH

1U12BU1ERH

1U15RU1ERE

1U18RU1ERE

1U24SU1ERE

Note:

3OHDVHPDNHVXUHWKHSRZHUVXSSO\FRUUHFWO\DWƪUVWNNYROWDJHZKLOHNNNYROWDJH

Summary of content (10 pages)

PAGE 1
Ductless Split Air Conditioner Installation Manual Note: Indoor AS09TB1HRH AS12TB1HRH AS15TD1HRE AS18TD1HRE AS24TE1HRE Outdoor 1U09BU1ERH 1U12BU1ERH 1U15RU1ERE 1U18RU1ERE 1U24SU1ERE 3OHDVH PDNH VXUH WKH SRZHU VXSSO\ FRUUHFWO\ DW ƪUVW N N YROWDJH ZKLOH N N N YROWDJH Table of Contents Step 1 - Preparation ...................................................................................................................... 2 Step 2 - Installation of the Indoor Unit ..............
PAGE 2
ENGLISH Step 1 - Preparation Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Ţ Required Tools for Installation Procedure for Selecting the Location Drill :LUH Snipper +ROH 6aZ Ş VDFXXP SXPS Soap-and-wDWHU VROXWLRQ RU JDV OHDkDJH detector TRUTXH ZUHQFK PP PP PP TXELQJ FXtter FODULQJ tool RazRU NQLIH 0HDVXULQJ WDSH Level MicrRQ JDXJH NitrRJHQ Mini-SSOLW $' $GDSWHU Ş tR Ş $ 1RQ DGKHVLYH Tape % $GKHVLYH Tape & 6DGGOH /.
PAGE 3
Step 2 - Installation of the Indoor Unit Attaching the Mounting Plate to the Wall ENGLISH 2.1 Step 2.1 Using a stud sensor, locate and mark the stud positions in the wall where the indoor unit is to be mounted. 2.2 Step 2.2 Place the mounting plate on the wall in the desired location taking into account the minimum clearances necessary for proper operation. Step 2.1 Step 2.2 Step 2.3 Step 2.4 Step 2.5A Step 2.5B Step 2.6 Step 2.7 Step 2.8A Step 2.
PAGE 4
Mounting the Indoor Unit Onto the Wall Plate ENGLISH 2.9 Step 2.9 With the top of the indoor unit closer to the wall, hang the indoor unit on the upper hooks of the mounting plate. Slide the unit slightly side to side to verify proper placement of the indoor unit on the mounting plate. Rotate the lower portion of the indoor unit to the mounting plate, and lower the unit onto the lower hooks of the mounting plate. (Illustration 2) Verify the unit is secure. 2.10 Step 2.10 Step 2.9 Step - 2.
PAGE 5
3.3 Step - 3.3 3.4 Step 3.3 ENGLISH Connect the wiring for both the power source and indoor wiring. Wire the system according to applicable national / local codes. Verify that the wiring connections for the indoor unit match wire for wire. (1-1, 2-2, 3-3, Gnd-Gnd). Failure to wire the system correctly may lead to improper operation or component damage. Step 3.4 Step - 3.4 Replace the cover plate. Step 4 - Interconnecting the Indoor and Outdoor Units *See Steps 2.11 - 2.13 & 3.2 - 3.
PAGE 6
Step 5 - Leak Test and Evacuation ENGLISH Leak Test +D]DUG RI ([SORVLRQ 1HYHU XVH DQ RSHQ ƫDPH WR GHWHFW JDV leaks. Explosive conditions may occur. Use a leak test solution or other approved methods for leak testing. Failure to follow recommended safe leak test procedures could result In death RU VHULRXV LQMXU\ RU HTXLSPHQW RU SURSHUW\ GDPDJH Use only dry nitrogen with a pressure regulator for pressurizing unit.
PAGE 7
piping hole. Use a sealant to seal the piping hole opening to prevent weather elements from entering the building. (Illustration 6) It becomes The end is imm- It waves. The gap with the There is the bad high midway. ersed in water. ground is too small smell from a sewer Illustration 6 Step 6 - Charging See Steps 5.2 - 5.5 for evacuating the system prior to charging. The standard lineset length is 25ft. If the installation OHQJWK LV GLƩHUHQW DGMXVW WKH UHIULJHUDQW FKDUJH E\ R] IW for the 9K, 12K,
PAGE 8
ENGLISH Section 7 - Explaining Operation to the End User Ţ 8VLQJ WKH 23(5A7,1* ,16758&7,216 H[SODLQ WR WKH XVHU KRZ WR XVH WKH DLU FRQGLWLRQHU WKH UHPRWH FRQWUROOHU UHPRYLQJ fRU RSHUDWLRQ HWF Ţ 5HFRPPHQG WKDW WKH XVHU UHDG WKH 23(5A7,1* ,16758&7,216 FDUHIXOO\ Model Name Operating Range Power Supply Electrical Data Refrigerate Line System Outdoor Indoor Cooling °F(°C) Heating °F(°C) Voltage, Cycle, Phase V/Hz/Compressor Type Maximum Fuse Size A Minimum Circuit Amp A Connections Liquid O.D.
PAGE 9
[This page intentionally left blank.
PAGE 10
Model #: 1U09BU1ERH，1U12BU1ERH 1U15RU1ERE, 1U18RU1ERE，1U24SU1ERE Issued Date: Nov,2016