Installation guide

ManualsBrandsHaier ManualsAir HandlerOfficial Haier ductless split a/c

Ductless Split Air Conditioner

Indoor

AW09EH2VHA

AW12EH2VHA

AW18EH2VHA

Outdoor

1U09EH2VHA

1U12EH2VHA

1U18EH2VHA

Installation Manual

Step 1 - Preparation ...................................................................................................................... 2

Step 2 - Installation of the Indoor Unit ........................................................................................... 3

Step 3 - Installation of the Outdoor Unit ........................................................................................ 4

Step 4 - Interconnecting the Indoor and Outdoor Units ................................................................. 5

Step 5 - Leak Test and Evacuation .................................................................................................. 6

Step 6 - Charging ........................................................................................................................... 7

Section 7 - Explaining Operation to the End User ........................................................................... 8

.................................................................................................. 8

Section 9 - S

0010586954

eacoast Application ................................................................................................... 8

Table of Contents

Summary of content (10 pages)

PAGE 1
Ductless Split Air Conditioner Installation Manual Indoor AW09EH2VHA AW12EH2VHA AW18EH2VHA Outdoor 1U09EH2VHA 1U12EH2VHA 1U18EH2VHA Table of Contents Step 1 - Preparation ...................................................................................................................... 2 Step 2 - Installation of the Indoor Unit ........................................................................................... 3 Step 3 - Installation of the Outdoor Unit .......................................
PAGE 2
ENGLISH Step 1 - Preparation • • • • • • • • • • • • • • • • • • • • • • Required Tools for Installation Procedure for Selecting the Location Drill Wire Snipper Hole Saw 2 3/4” Vacuum pump Soap-and-water solution or gas leakage detector Torque wrench 17mm, 22mm, 26mm Tubing cutter Flaring tool Razor knife Measuring tape Level Micron gauge Nitrogen Mini-Split AD-87 Adapter (1/4” to 5/16”) A - Non-adhesive Tape B - Adhesive Tape C - Saddle (L.S.
PAGE 3
Step 2 - Installation of the Indoor Unit Attaching the Mounting Plate to the Wall ENGLISH 2.1 Step 2.1 Using a stud sensor, locate and mark the stud positions in the wall where the indoor unit is to be mounted. 2.2 Step 2.2 Place the mounting plate on the wall in the desired location taking into account the minimum clearances necessary for proper operation. Step 2.1 Step 2.2 Step 2.3 Step 2.4 Step 2.5A Step 2.5B Step 2.6 Step 2.7 Step 2.8A Step 2.
PAGE 4
Mounting the Indoor Unit Onto the Wall Plate ENGLISH 2.9 Step 2.9 With the top of the indoor unit closer to the wall, hang the indoor unit on the upper hooks of the mounting plate. Slide the unit slightly side to side to verify proper placement of the indoor unit on the mounting plate. Rotate the lower portion of the indoor unit to the mounting plate, and lower the unit onto the lower hooks of the mounting plate. (Illustration 2) Verify the unit is secure. 2.10 Step 2.10 Step 2.9 Step - 2.
PAGE 5
3.3 Step - 3.3 3.4 Step 3.3 ENGLISH Connect the wiring for both the power source and indoor wiring. Wire the system according to applicable national / local codes. Verify that the wiring connections for the indoor unit match wire for wire. (1-1, 2-2, 3-3, Gnd-Gnd). Failure to wire the system correctly may lead to improper operation or component damage. Step 3.4 Step - 3.4 Replace the cover plate. Step 4 - Interconnecting the Indoor and Outdoor Units *See Steps 2.11 - 2.13 & 3.2 - 3.
PAGE 6
Step 5 - Leak Test and Evacuation ENGLISH Leak Test Hazard of Explosion! Never use an open flame to detect gas leaks. Explosive conditions may occur. Use a leak test solution or other approved methods for leak testing. Failure to follow recommended safe leak test procedures could result In death or serious injury or equipment or property damage. Use only dry nitrogen with a pressure regulator for pressurizing unit.
PAGE 7
piping hole. Use a sealant to seal the piping hole opening to prevent weather elements from entering the building. (Illustration 6) It becomes The end is imm- It waves. The gap with the There is the bad high midway. ersed in water. ground is too small smell from a sewer Illustration 6 Step 6 - Charging See Steps 5.2 - 5.5 for evacuating the system prior to charging. The standard lineset length is 25ft. If the installation length is different, adjust the refrigerant charge by .2 oz / ft.
PAGE 8
Section 7 - Explaining Operation to the End User ENGLISH • Using the OPERATING INSTRUCTIONS, explain to the user how to use the air conditioner (the remote controller, removing for operation, etc.) • Recommend that the user read the OPERATING INSTRUCTIONS carefully. Model Name Operating Range Power Supply Electrical Data Refrigerate Line System Outdoor Indoor Cooling °F(°C) Heating °F(°C) Voltage, Cycle, Phase V/Hz/Compressor Type Maximum Fuse Size A Minimum Circuit Amp A Connections Liquid O.D.
PAGE 9
[This page intentionally left blank.
PAGE 10
www.Haier.com Model #: AW09EH2VHA, 1U09EH2VHA AW12EH2VHA, 1U12EH2VHA AW18EH2VHA, 1U18EH2VHA Issued Date: November 2015 Haier America, Wayne, NJ 07470 ©2015 Haier America Trading, LLC.