PLASMA TV OWNER`S MANUAL MODELS: 42EP24STV Please read this manual carefully and completely before operating the unit, and retain this manual for future reference.
WARNING RISK ELECTRIC SHOOK DO NOT OPEN WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel. Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product.
IMPORTANT SAFETY INSTRUCTIONS Read all of the instructions before using this appliance. When using this appliance, always exercise basic safety precautions, including the following: 1)Save these Instructions ---the safety and operating instructions should be retained for future reference. 2)All warning on the appliance and in the operating instructions should be followed. 3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
b.If liquid has been spilled, or objects have been fallen into the unit. c.If the unit has been exposed to rain or water. d.If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. e.If the unit has been dropped or damaged in any way. f.
Warning..............................................................2 Safety Instructions............................................ 3-4 Introduction Controls...........................................................6 Connection Options...........................................7 R emote Control Key Functions ...........................8 Installing Batteries............................................8 Installation Installation instructions....................................9 VCR Setup..................
Front panel controls EXIT INPUT VOL VOL MENU Menu exit Power On/Off Button Signal source input option Down/Up. Sele ct desired option on MENU or tune to the desired channel.
Real panel controls S-Video Input VGA Input/Audio input DVI Input/Audio input connect your cable/PC through the input Power On/Off Earphone port 0 VGA IN COMPONENT IN R DVI IN AV IN AV OUT L SWITCH AUDIO OUT VGA AC-INPUT AUDIO Pr/Cr Pb/Cb Y L-AUDIO-R DVI AUDIO VIDEO L-AUDIO-R S-VIDEO L-AUDIO-R ANT IN Audio/Video Input Connect audio/video output from an external device to these jacks DVD/DTV Input Connect a component video/audio device to these jacks AUDIO output VIDEO External aud
When using the remote control. Aim it towards the remote sensor on the TV. Function introduction FREEZE Freezes the currently-viewed picture. INPUT Ratates the source input mode. MUTE SLEEP Press this key to set sleeptimer. PC Select PC source AUTO Auto adjust for PC Switches the sound on or off PC FREEZE INPUT POWER AUTO SLEEP MUTE DISPLAY POWER Turns your TV or any other programmed equipment on or off, depending on mode.
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. PC VIDEO INPUT AUTO DVI MUTE POWER DISPLAY MENU DNR AVC EXIT ENTER P.STD CALENDAR / SAVING CC VOLARC SURROUND RATING SLEEP FREEZE S.STD Speaker unit(X2) 1 4 M4X12 Screws x8 Standx1 VOL+ LOCK Connecting block X4 2 (2.
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV Do not leave a still picture from a VCR on the screen for a long If the 4:3 format is used, the fixed images on the sides of the screen may remain visible on the screen, if this format is used day after day. This is known as burn-in, it is uneven wear of the screen area. Reduce contrast when displaying fixed images on the screen for a long 1.
How to connect Connect the audio and video cables from the external equipment's output jacks to the TV`s AV IN input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). How to use 1. Select the input source by using the INPUT button on the remote control. 2 . Operate the corresponding external equipment. Refer to external equipment operating guide. How to connect 1 .
- To watch digitally broadcast programs, purchase and connect a digital set-top box. Digital Set-top Box How to connect Use the TV`s COMPONENT (Y, Pb, Pr) IN jacks, VGA or DVI IN port for video connections, depending on your set-top box connections available. Then, make the corresponding audio connections. Signal 480i 480p 720p set-top box.) 2 . Use INPUT on the remote control to select YPbPr/YCbCr, VGA, or DVI source. 1080i 1080p How to use 1 . Turn on the digital set-top box.
How to connect 1. To get the best picture quality, adjust the PC graphics card, if necessary. 2. Use the TV `s VGA IN or DVI (Digital Visual Interface) IN port for video connections, depending on your PC connector. If the graphic card on the PC does not output analog or digital RGB simultaneously, connect only one of either VGA IN or DVI IN to display the PC on the TV.
Install the Speakers 1 Face the PDP screen upside down on a clean blanket or a bracket and pay attention not to indent the casing. Lay the two speaker aside of the PDP. 2 . Fix 4 ST4X16 screws to the speaker. (position , , and in Figure ) 3 . Lean the speaker against the plasma screen, ensuring that the screw holes on the connecting block in line with the screw holes on the plasma screen, and hold the speaker. (position I, II, III and IV in Figure ) 4 .
Install the Stand Install the PMMA Baffle After installing the brace pole(see figure below) rip the protective sheet off of the PMMA baffle and put the baffle into the stand. Install the brace pole 1 After put the brace pole to the stand, use the screw 8 M4x12 to fix it. 2 Take care not to touch the stand and the brace pole; 3 Fix the PMMA baffle with the screw 2 M4X8rom the front .
* In this manual, the OSD (On Screen Display) may be different from your TV `s, because it is just an example to help you with the TV operation. TV Turning on the TV just after installation. 1 . Connect power cord correctly. 2. Press the SWITCH button on back of the TV. At this moment, the TV is switched to standby mode. Press the POWER button on the remote control or button on the TV and then the TV will turn on. Turning on the TV 1 .
Basic Function Function Operation Menu 1.Press MENU button to open the main menu. Press VOL+/- button to select PIC., SOU., ADJ., SYS. , FUN. or TIME menu. 2.Press CH+/- button to select submenu, and press VOL+/- button to increase/decrease the value or select the setup. 3.Press MENU to return to the main menu. 4.The setup time in display will disappear automatically when the latest preset time expiries. MENU display time can be set to 5,10,15,20,25,30 and 40 seconds. 5.
System Menu This TV set has three methods to set channels, which are respectively Automatic search, manual search In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV set to set channel. fine tune. Channel Type Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system).
System Menu Fine Tune If the picture and/or sound are poor, try using the fine tune feature. Do not use this feature unless reception is poor. 1 Repeat step 1-2, then press CH+/- buttons to select "Fine Tune" item. 2 Press VOL-/+ buttons repeatedly to carry out fine tune, till the best Color Sys. Sound Sys. Fine Tune Skip Channel Type CATV Type Auto Scan Prog. Switch AUTO M/N 49.75MHz Off Cable STD picture and sound are obtained, then loosen the button.
Picture Quality Adjust Picture Quality Adjust The TV menu gives you an overview of MENU you can select. Note: Depending on the input signal, one or more menu items may not be selectable. 1 Press MENU and then use VOL+/- button to select the PIC. Menu. 2 Press CH+/-button to select the desired items. 3 Press VOL+/- button to adjust the setting. 4 When you are satisfied with your choice, press MENU button to return to the previous menu or press EXIT button to return to TV viewing.
Sound adjustment Sound Adjust Sound can be adjusted for any input as follows: 1. Press MENU button and then use VOL+/- button to select the SOU.menu. 2. Press CH+/- button for desired option. 3. After your option is selected, press VOL+/- button to adjust. 4. Repeat step 2 and 3 until desired sound has been achieved when displayed time for menu setup expires without any operation , MENU disappears from the picture .
Adjustment Setup Adjustment Setup VGA/DVI: In VGA and DVI input mode , H Position and V Position can be used to adjust the picture position. Display Mode When VGA DVI input mode is set Adjust 1. Press MENU button on the remote controller and then use the VOL+/- to select the ADJ.menu. Reset 2. Press CH+/- to enter MENU of picture position setup Auto Sync. 3. Press the VOL+ button and then use CH+/- button for desired adjust parameter option.
Function Setup Function Setup It is possible to select Menu Language, OSD translucent, position and screen display of MENU as follows: 1. Press MENU button once, and then use VOL+/- button until the following menu appears on the screen: 2. Press the VOL+ button and then use CH+/- button on the remote controller to enter MENU of system setup. 3. Press CH+/- to select desired option on MENU. AV1 4. Press VOL+/- to adjust selected option.
Close Caption Closed captioning is a process which converts the audio portion of a television program into written words which then appear as subtitles on the television screen. Closed captions allow viewers to read the dialogue and narration of television programs. Using Closed Captions Captions are the subtitles of the dialogue and narration of television programs. For prerecorded programs, program dialogue can be arranged into captions in advance.
Continue Parental Ratings for Movies previously shown in theaters: Movie Ratings : NR (Permits all programs) G (General audience) PG (Parental guidance suggested) PG-13 (Parents strongly cautioned) R (Restricted) NC-17 (No one 17 and under admitted) X (Adult only) If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.
Time Setup If Off-time or On-time is intended in AV1/S-Video/YPbPr/YCbCr/VGA , follow the instructions as below: Clock Setting The clock will only work if the TV set is turned on or in standby. When the set is disconnect from the power supply or is turned off by the main power on the rear panel, the clock loses power and will need to be reset when the power is reconnected. 1 Press MENU button and then VOL+/- button to select the TIME menu.
Lock Menu Options - The TV has the function of security default lock. Password needs to be entered when the program lock mode is to be set. Lock Setup Press LOCK button on remote control, Password will appear on the screen. If password is correctly entered, the Lock set menu will be menu willl be entered. If the password is not correctly entered, you will be required to reenter the password and the cursor will stay At the first place. Press EXIT to erase the window.
Prog.Num Prog. Num is opted for setting up preset channel. Press CH+/- button to select Prog Num. Press VOL+/- button, to select channel number.(The item is not available except TV signal.) Source Lock Source Lock is opted to hinder external input modes, such as AV, S -Video and VGA. Press CH+/- button to select the option, and press VOL+/- button to display Source Lock menu. Press CH+/- button to select desired option. Press VOL+/- button to set up the mode of Source Lock.
- RGB (PC) mode only; This function doesn`t work for RGB-DTV mode. Automatically adjusts picture position and minimizes image shaking. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. The Auto sync are not active in DVI mode. 1 . Press MENU button and then use VOL+/- button to select the ADJ. Menu. 2 . Press CH+/-button to select Auto Sync. 3 . Press VOL+/- button to run Auto Sync.
Check whether the TV is turned on from both front button and t he back switch. No picture & No sound Is the power cord inserted into wall power outlet? Test the wall power outlet, plug another product`s power cord into the outlet where the TV`s power cord was plugged in. Picture OK & No sound Press the VOL+ button. Sound muted? Press MUTE button. Check to see if there is any object between the TV and the remote control causing obstruction.
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. 1 . Here`s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it`s almost dry, and then use it to wipe the screen. 2.
MODEL Dimensen(WXHXD) Unit::inches/mm (main compoment) Weight (pounds / kg) Resolution 42EP24STV 41.3x3.4x26.1/1050x664x86 60.6/27.5 852x480(Dot) Power requirement ~110/220 Volts , 50/60Hz Color System Color Operating Temperature Range Operating Humidity Range Maximum Elevation Impedance Speakers 8 Input consumption 2x10W Size(WxHxD) (inches/mm) 4.3x21.9x2.4/110x556x62 Weight (pounds/kg) 2x5.5/2x2.5 The specifications shown above may be changed without notice for quality improvement.
V0.
