User Manual Refrigerator-Freezer HBM450WH1 HBM450SA1
Thank You Thank you for purchasing a Haier Product. Please read these instructions carefully before using this appliance. The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance. Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance.
Intended Use Content Intended use Intended Use..................................................................................................................................... .5 Safety.................................................................................................................................................. .6 Product Description.......................................................................................................................10 Use............................
Safety Before switching on the appliance for the first time do… ▶▶ make sure there is no transport damage. ▶▶ make sure all packaging is removed and is kept out of children´s reach. ▶▶ wait at least two hours before installing the appliance in order to ensure the refrigerant circuit is fully efficient. ▶▶ handle the appliance always with at least two persons because it is heavy. ▶▶ install the appliance in a well-ventilated place. Ensure a space of at least 5 cm above and 5 cm around the appliance.
Safety Safety if it is left for a long period at a temperature above or below the indicated range. ▶▶ check the condition of food if a warming in the freezer has takenplace. During daily use do not… xx set unnecessarily low temperature in the refrigerator compartment. Minus temperatures may occur at high settings. Attention: Bottles can burst. xx store medicines which need a precision storage temperature or bacteria or chemical agents in the appliance.
Use Product Description Before first use 1 13 2 3 4 5 6 ▶▶ Remove all packaging materials, keep them out of children`s reach and dispose them in an environmentally friendly manner. ▶▶ Clean the inside and outside of the appliance with water and a mild detergent before putting any food in it. ▶▶ After the appliance has been levelled and cleaned, wait for at least 2 hours before connecting it to the power supply. See Section INSTALLATION.
Use Use Sensor keys Control panel The buttons on the control panel are sensor keys, which already respond when lightly touched with the finger. Switch on /off the appliance a1 a2 The appliance is in operation as soon as it is connected to the power supply. When the appliance is powered on for the first time, indicator “c2” is shining on the display until the temperature reaches -5°C or after 1 hour working.
Use Use Lock/unlock panel Adjust the temperature for freezer ▶▶ Touch button “G” for 3 seconds to block all panel elements against activation. The related indicator “g” is now displayed. ▶▶ For unlocking press again the button. 1. 2. Lock Hold 3 Sec. 3. Notice The control panel is automatically blocked against activation if 30 seconds no button is pressed. For any settings the control panel must be unlocked. 4.
Use Use Fuzzy mode Notice The Super-freeze function will automatically switch off after 56 hours. The appliance is then operated at the previously set temperature. Fuzzy Fuzzy My Zone box The fridge compartment is equipped with a My Zone box. In accordance with the food’s storage demands, the most suitable temperature can be selected to get the optimal nutritional value of the foods. Storage temperature can be adjusted between -3°C and 5°C.
Use Use Tips on storing fresh food Storage into the freezer compartment Storing into the refrigerator compartment ▶▶ Keep your fridge temperature below 5°C. ▶▶ Hot food must be cooled to room temperature before storing in the appliance. ▶▶ Foods stored in the refrigerator should be washed and dried before storing ▶▶ Food to be stored should be properly sealed to avoid odour or taste alterations. ▶▶ Do not store excessive quantities of food.
Equipment Equipment Multi-air-flow Ice cube tray The refrigerator is equipped with a multi-air-flow system, with which cool air flows are located on every shelf level. This helps to maintain a uniform temperature to ensure that your food is kept fresher for longer. 1. 2. Fill the ice cube tray 3/4 full of water, close t with the cover and put it into the pre-freezing compartment. Twist the ice cube tray slightly or hold it under flowing water to loosen the ice cubes.
Care and Cleaning Care and Cleaning WARNING! Disconnect the appliance from the power supply before cleaning. Cleaning Clean the appliance when only little or no food is stored. The appliance should be cleaned every four weeks for good maintenance and to prevent bad stored food odors. WARNING! ▶▶ Do not clean the appliance with hard brushes, wire brushes, detergent powder, petrol, amyl acetate, acetone and similar organic solutions, acid or alkaline solutions.
Troubleshooting Troubleshooting Many occuring problems could be solved by yourself without specific expertise. In case of a problem please check all shown possibilities and follow below instructions before you contact an after sales service. See CUSTOMER SERVICE. WARNING! ▶▶ Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.
Installation Troubleshooting Problem Possible Cause The appliance makes abnormal sounds. • The appliance is not located on • Adjust the feet to level the aplevel ground. pliance. • The appliance touches some ob- • Remove objects around the ject around it. appliance. A slight sound is • to be heard similar Possible Solution • This is normal. to that of flowing water. Unpacking WARNING! ▶▶ The appliance is heavy. Always handle with at least two persons.
Installation Installation 1. 2. max 45° 3. Aigning the appliance Door Reversibility The appliance should be placed on a flat and solid surface. 1. Tilt the appliance slightly backwards. 2. Set the feet to the desired level. Make sure the distance to the wall on the hinge side is at least 100 mm for the door to open properly. 3. The stability can be checked by alternately bumping on the diagonals. The slightly swaying should be the same in both directions.
Technical Data Installation 13. 13. Change the positions of the blanking plugs and the screw on the side. Trade mark a b a Remove lower door b Change the positions of the blanking plug at the top of the lower door. Model No. Category of the model Voltage / Frequency c e d f 14. 15. 17. 19. 16. 18.
